Jack Stands vs Mower Ramps: Which One Should You Buy?
Jack stands and mower ramps compared on capacity, height, weight and access, with two examples of each side and a verdict for under-deck work.
On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
VEVOR 6 Ton Jack Stands 14.2-23 inch Double Locking9.7/10View on Amazon - 2
55" L Aluminum Shed Ramps for Lawn Mowers9.5/10View on Amazon - 3
ANTPOWER 3 Ton Double Locking Jack Stands9.7/10View on Amazon - 4
Jack Stands 3 Ton with Double Locking and Large Foot Base CarView on Amazon - 5
Jack Stands 3 Ton with Double Pin Lock and Large Foot BaseView on Amazon - 6
Amazon Basics Steel Jack Auto StandsView on Amazon - 7
Pro-LifT PL3300 Heavy Duty Jack Stands For CarView on Amazon - 8
Pro-Lift T-6906D Double Pin Jack StandView on Amazon - 9
BIG RED T46002A Torin Steel Jack Stands: Double LockingView on Amazon
Verdict: Choose jack stands if the job is holding a mower or vehicle up for work underneath, after lifting with a jack. Choose mower ramps if the job is moving a mower into a shed, garage, barn or trailer, or up to a raised entrance.
The jack stands vs mower ramps question comes down to what the lift is for. A jack stand holds a raised vehicle in place while work happens underneath. A mower ramp gives wheels a slope to climb, so a mower can roll into a shed or onto a trailer. This comparison covers the differences, then examples of each side.
AcreMowerLab earns a commission when you shop through links here. It never changes your price. Affiliate disclosure.
PRUTHY Jack Stands with Double Locking and Large Foot Base
A 3 ton jack stand pair with double locking, metal safety pins, a wide pyramid foot base, and a height range of 11.4 to 16.9 inches for holding a lifted vehicle in place.
Who it's for: owners who lift a mower or vehicle with a jack and need stands to hold it for under-deck work.
Who should skip it: anyone who needs a slope for loading a mower into a shed or trailer, which is a ramp job.
Read the full review
The PRUTHY pair lists 3 ton at 6,600 lb, 11.4 to 16.9 inches, a stamped steel welded frame, and a ductile iron ratchet bar in one piece. Its double locking pairs a locking ratchet bar with metal safety pins, and its wide pyramid foot base and large saddle are listed for stable support. The listing states US safety standards and a limited 1-year manufacturer warranty.
Pros
- Double locking with metal safety pins
- Height range of 11.4 to 16.9 inches
- Stamped steel frame, ductile iron ratchet bar
- 1 Year Limited Manufacturer warranty stated
Cons
- Weight is not stated
- Maximum height of 16.9 inches
- For holding only, not for lifting a vehicle
- Sawtooth height steps, not continuous adjustment
VEVOR Jack Stands 3 Ton Capacity, 10.8-16.3 inch Adjustable Height
A 3 ton jack stand pair with a carbon steel base, a cast iron ratchet bar, and a height range of 10.8 to 16.3 inches across 9 levels, for holding a lifted vehicle in place.
Who it's for: owners who lift a mower or vehicle with a jack and need stands to hold it for work underneath.
Who should skip it: anyone who needs a slope for loading, which is a ramp job. Note also: the title gives 6,000 lbs while the bullets give 6,600 lbs, and the spec table lists NumberOfItems as 1 while the title says 1 Pair.
Read the full review
The VEVOR pair lists 3 ton, 10.8 to 16.3 inches across 9 levels, a carbon steel base, and a cast iron ratchet bar with a rust-proof coating. Its wide pyramid base, triangular foot pad, and notched saddle are listed for a stable grip, and the listing states CE standards. The spec table lists 11.0 pounds.
Pros
- Height range of 10.8 to 16.3 inches across 9 levels
- Carbon steel base and cast iron ratchet bar
- Wide pyramid base and notched saddle
- CE standards stated
Cons
- Capacity stated two ways in title and bullets
- Warranty description lists NO
- For holding only, not for lifting a vehicle
- Height range tops out at 16.3 inches
Arejonner 72.5 inch Folding Loading Ramps, 1500 lb Capacity, Pack of 2
A folding loading ramp pair with a sandblasted perforated surface, safety straps, and a total capacity of 1,500 lbs for loading mowers into sheds, barns, garages, or trailers.
Who it's for: owners who load mowers, ATVs, motorcycles, or garden equipment into sheds, barns, garages, or trailers, and who want a folding pair for storage.
Who should skip it: anyone who needs to hold a vehicle up for work underneath, which is a stand job. Note also: the title and bullets give 72.5 inches unfolded, while the spec table lists 71.0 inches, and the spec table lists NumberOfItems as 1 while the title says Pack of 2.
Read the full review
The Arejonner pair lists 1,500 lbs total at 750 lbs per ramp, 72.5 inches unfolded, 38.1 inches folded, and a maximum incline height of 31.5 inches. Each ramp weighs 17 lbs with built-in handles, and the pair includes four safety straps and gloves, a perforated sandblasted surface for traction, alloy construction, and integrated tailplates.
Pros
- Folds to 38.1 inches for compact storage
- Each ramp weighs 17 lbs with built-in handles
- Four safety straps and gloves included
- Perforated sandblasted surface for traction
Cons
- Title length differs from spec table length
- Maximum incline height of 31.5 inches
- No warranty term is stated
- For loading only, not for holding a vehicle up for work
TraiNexalign 36 x 48 Inch Shed Garage Access Ramps, 1500 lbs Capacity
A shed and garage access ramp pair with an anti-slip punch plate surface and a capacity of 1,500 lbs for loading riding mowers and other equipment into sheds and garages.
Who it's for: owners who need a shed or garage access ramp for riding mowers and heavy garden equipment.
Who should skip it: anyone who needs to hold a vehicle up for work underneath, which is a stand job, or who needs a folding ramp for tight storage. Note also: the title gives 36 x 48 inches, while the spec table lists 38.58 x 26.38 x 4.33 inches.
Read the full review
The TraiNexalign pair lists 1,500 lbs, an anti-slip punch plate surface with dense punched holes, reinforced edges, and resistance to corrosion, rust, and wear. It is made for loading riding mowers, motorcycles, tractors, snow blowers, and garden carts into sheds, garages, barns, or trucks, with no tools needed. The spec table lists 48.0 pounds.
Pros
- Anti-slip punch plate surface
- Capacity of 1,500 lbs
- No tools needed for setup
- Resistant to corrosion, rust, and wear
Cons
- Title size differs from spec table dimensions
- No warranty term is stated
- No folding design is stated
- For loading only, not for holding a vehicle up for work
Other machines to compare
Jack Stands 3 Ton with Double Locking and Large Foot Base CarCheck price on Amazon
Jack Stands 3 Ton with Double Pin Lock and Large Foot BaseCheck price on Amazon
Amazon Basics Steel Jack Auto StandsCheck price on Amazon
Pro-LifT PL3300 Heavy Duty Jack Stands For CarCheck price on Amazon
Pro-Lift T-6906D Double Pin Jack StandCheck price on Amazon
BIG RED T46002A Torin Steel Jack Stands: Double LockingCheck price on Amazon
Jack stands vs mower ramps side by side
| Factor | PRUTHY Jack Stands | VEVOR Jack Stands | Arejonner Ramps | TraiNexalign Ramps |
|---|---|---|---|---|
| Capacity | 3 ton (6,600 lb) | 3 ton (title 6,000 lbs, bullets 6,600 lbs) | 1,500 lbs total, 750 lbs per ramp | 1,500 lbs |
| Height or length | 11.4-16.9 inches | 10.8-16.3 inches | 72.5 inches unfolded, 38.1 inches folded | 36 x 48 inches (title) |
| Weight | Not stated | 11.0 pounds | 17 lbs per ramp | 48.0 pounds |
| Safety | Double locking, safety pins | CE standards, pyramid base | Perforated surface, safety straps | Anti-slip punch plate |
| Warranty | 1 Year Limited Manufacturer | NO (spec table) | Not stated | Not stated |
| Best at | Holding a lifted vehicle | Holding a lifted vehicle | Loading into sheds and trailers | Shed and garage access |
Figures are manufacturer stated for the example models, collected 1 November 2026.
Holding it up: jack stands
A jack stand does not lift. The PRUTHY listing says its stands help support vehicles after lifting with a jack. The PRUTHY pair lists 11.4 to 16.9 inches, 3 ton at 6,600 lb, a stamped steel welded frame, and a ductile iron ratchet bar in one piece. The VEVOR pair lists 10.8 to 16.3 inches across 9 levels, a carbon steel base, a cast iron ratchet bar, CE standards, and a wide pyramid base with a notched saddle. Note: the VEVOR title gives 6,000 lbs, while its bullets give 6,600 lbs.
Driving it up: mower ramps
A ramp does not hold a vehicle up for work. Both ramp examples list 1,500 lbs. The Arejonner pair folds, weighs 17 lbs per ramp, lists 750 lbs per ramp, and includes four safety straps and gloves, with a perforated sandblasted surface for traction. The TraiNexalign pair is a shed and garage access ramp with an anti-slip punch plate surface and reinforced edges, with no tools needed for setup. Its title gives 36 x 48 inches, while its spec table lists 38.58 x 26.38 x 4.33 inches.
Capacity and height: what separates the sides
Stands are described by a height range for holding: 11.4 to 16.9 inches for PRUTHY, and 10.8 to 16.3 inches for VEVOR. The ramp examples are described by size and access: Arejonner unfolds to 72.5 inches with a maximum incline height of 31.5 inches, while TraiNexalign is sized for a shed or garage entrance. The stand examples list 3 ton and the ramp examples list 1,500 lbs, so compare the figures for the job at hand rather than treating one side as a direct substitute for the other.
Handling, storage and upkeep
Stands are steel tools with welded frames and ratchet bars. For portability, Arejonner folds to 38.1 inches and carries by built-in handles, while TraiNexalign is placed between ground and entrance and adjusted for angle, with no tools needed. The TraiNexalign listing states no folding design.
The examples
Acreage and terrain fit
PRUTHY Jack Stands
VEVOR Jack Stands
Arejonner Ramps
TraiNexalign Ramps
Matching It to Your Property
- On flat ground near a shed or garage, a ramp gives a mower a slope into the entrance, while stands hold a lifted mower for under-deck work.
- Where storage is tight, Arejonner folds to 38.1 inches long, while TraiNexalign lists no folding design.
- Where an entrance is raised, check ramp length and incline height against it: Arejonner lists a maximum of 31.5 inches.
- For under-deck work, stands hold a vehicle after lifting, while ramps move a mower rather than hold it up.
The Acre Score explained
The Acre Score weighs performance, build, value, safety, and warranty, each from stated specs. A factor not stated scores zero, which is why only one example scores for warranty.
| Product | Acre Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| PRUTHY Jack Stands | 9.7 | 30 | 21 | 20 | 9 | 3 |
| VEVOR Jack Stands | 9.6 | 29 | 20 | 20 | 7 | 0 |
| Arejonner Ramps | 9.5 | 28 | 20 | 20 | 7 | 0 |
| TraiNexalign Ramps | 9.5 | 27 | 19 | 19 | 6 | 0 |
Scores run from 9.2 to 9.8: each product’s point total is placed on that range, so more points always means a higher score.
If a lift for deck work is what you need, see Mower Lift vs Jack Stands for a third option.
Read the manual, keep children and pets out of the yard while you work, wear eye and hearing protection and sturdy footwear, and never exceed the slope rating of your machine. Refuel only with the engine off and cool. See CPSC lawn mower safety. Read our Safety Disclaimer.
FAQ: mowing large lots
Can a mower ramp hold a mower up for under-deck work?
No. Ramp listings describe loading into sheds, barns, garages and trailers, not holding a vehicle up for work underneath. Stand listings describe holding a vehicle after lifting with a jack.
Do jack stands lift a mower by themselves?
No. The PRUTHY listing says its stands help support vehicles after lifting with a jack. A jack does the lifting, and the stands hold the raised vehicle in place.
What capacity do the stand examples list?
Both stand examples list 3 ton. The PRUTHY pair lists 6,600 lb, while the VEVOR title gives 6,000 lbs and its bullets give 6,600 lbs, so the VEVOR capacity figure is stated two ways.
What should be checked before using a ramp?
Check the surface and capacity against the entrance, and, where the listing gives them, straps and incline height. Arejonner lists a perforated sandblasted surface, four safety straps, 1,500 lbs total, and a maximum incline height of 31.5 inches.
Which side suits a shed with a raised entrance?
Ramps. TraiNexalign is made for shed and garage access, and Arejonner is made for loading into sheds, barns, garages and trailers. Check ramp length and incline height against that entrance before buying.
More mowing guides
- Mower Lift vs Jack Stands: Which One Should You Buy?
- Mower Ramps vs Mower Lift: Which One Should You Buy?
- Best Mower Ramps for Sheds: 5 Picks
- Best Jack Stands for Riding Mower (2026)
A mower lift is a third option for deck work, covered in the related guides above.
