High Pressure Hose Repair Kit: What to Buy
A brass barb splicer and clamps rejoin a cut pressure washer hose, when the fitting matches the hose size and the damage is a clean cut.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
KOOTANS 32-Piece Brass Barb Splicer Kit9.6/10View on Amazon - 2
Ailbiuko 26-Piece Brass Barb Splicer Kit9.6/10View on Amazon
A cut in a pressure washer hose brings the wash to a stop, and a hose that leaks at the cut sends water across the driveway, the deck and the siding instead of through the nozzle. A high pressure hose repair kit puts the hose back to work: a brass barb splicer joins the cut ends, and a clamp on each side of the joint holds the splice tight. This guide shows how the repair works, how to size the fitting, and when a hose is past repair.
AcreMowerLab earns a commission when you shop through links here. It never changes your price. Affiliate disclosure.

KOOTANS 32-Piece Brass Barb Splicer Kit
Brass barb splicer kit with 32 fittings in 5 sizes and 46 stainless steel clamps, made from CA360 forged brass.
Who it's for: owners who want the most fittings in the box and forged brass barbs for water, fuel or air hose.
Who should skip it: anyone repairing 5/8 in hose, or anyone who needs a stated pressure rating before buying.
The KOOTANS kit holds 32 brass barb splicers in 5 sizes, from 3/16 in to 1/2 in, with 46 stainless steel pipe clamps. The fittings are CA360 forged brass, and the maker states the barb ends are smooth without burrs for a tight connection with the hose. The listing states use for water, fuel, air, oil and natural gas hose, and for industrial, automotive and plumbing work. It states no PSI rating and no warranty term.
Pros
- 32 fittings in 5 sizes, the larger fitting count here
- CA360 forged brass, thicker and stronger per the maker, with stainless steel clamps
- Barb ends are smooth without burrs, per the listing, for a tight fit to the hose
- 46 pipe clamps included across the 5 sizes
Cons
- No PSI rating is stated on the listing
- Warranty term is not stated on the listing
- No 5/8 in size, so it does not cover the largest hose the other kit covers
- Only 4 fittings in the largest 1/2 in size

Ailbiuko 26-Piece Brass Barb Splicer Kit
Brass barb splicer kit with 26 fittings in 6 sizes and 52 stainless steel clamps for air, fuel, water and oil hose.
Who it's for: owners who need several hose sizes covered, including 5/8 in hose, and want the most clamps in the box.
Who should skip it: anyone who needs a stated pressure rating on the fitting before buying.
The Ailbiuko kit holds 26 brass barb splicers in 6 sizes, from 3/16 in to 5/8 in, with 52 stainless steel clamps in 3 size ranges. The maker lists the fittings as brass and the clamps as stainless steel, and describes the joint as a firm connection when the clamps are fitted. The listing states use for air, fuel, water, oil and natural gas hose. It states no PSI rating and no warranty term, so check the hose rating before fitting a splice to a pressure hose.
Pros
- 6 sizes from 3/16 in to 5/8 in, the widest range here
- 52 stainless steel clamps included, in 8-12 mm, 9-16 mm and 13-19 mm sizes
- Brass fittings with stainless steel clamps for a firm connection, per the maker
- Suits air, fuel, water, oil and natural gas hose, per the listing
Cons
- No PSI rating is stated on the listing
- Warranty term is not stated on the listing
- Only 2 fittings in the largest 5/8 in size
- Only fittings and clamps are included; no hose cutter is listed in the box
How a high pressure hose repair kit works
A barb splicer is a short brass tube with barbs on each end. Cut out the damaged section, push a barb end into each hose end, then fit a clamp over each joint and tighten it. The barbs grip the inside of the hose, and the clamps press the hose wall onto the barbs so water stays in the hose. The kits in this guide carry barb splicers in sizes from 3/16 in to 5/8 in, with stainless steel clamps in the box.
| Barb size | Hose it fits |
|---|---|
| 3/16 in | Hose with a 3/16 in inside diameter |
| 1/4 in | Hose with a 1/4 in inside diameter |
| 5/16 in | Hose with a 5/16 in inside diameter |
| 3/8 in | Hose with a 3/8 in inside diameter |
| 1/2 in | Hose with a 1/2 in inside diameter |
| 5/8 in | Hose with a 5/8 in inside diameter |
Match the barb to the inside diameter of the hose. A barb that is too small can slip out under pressure, and a barb that is too large will not enter the hose. Measure the hose before ordering, and check the size printed on the hose or in the washer manual. See the pressure washer hose vs garden hose guide for how washer hose differs from garden hose.
The kits that make the repair
The splice needs a barb that matches the hose and clamps that fit over the joint, and the kits below carry both.
Fit the splice
Work with the washer off and the pressure released from the hose.
- Cut out the damaged section with a clean, square cut, and trim any frayed ends.
- Slide a clamp onto each hose end before you push the barb in.
- Push a barb end fully into each hose end.
- Position a clamp over each barb end and tighten it until snug.
- Reconnect the hose, turn the water on, and look for drips at the joints before washing.
Safety
Release the pressure from the hose before cutting it, and keep the washer off while the hose is open. Never point a pressure washer spray at people, animals or the person holding the hose, and keep children and pets clear of the work area. Wear eye protection while cutting hose and tightening clamps. Run gas washers outdoors only, and refuel with the engine off and cool.
When to replace the hose instead
A splice suits a clean cut in a hose that is sound on each side of the cut. Replace the hose when the damage sits close to an end fitting, when the cover is cracked or worn along a long run, or when a splice at the same spot keeps leaking. A hose that has burst along its length has lost its structure, so replace it rather than splicing it.
FAQ: mowing large lots
Can a high pressure hose repair kit fix a pressure washer hose?
It can join a clean cut, when the barb matches the hose size and the hose is sound on each side of the cut. Neither kit in this guide states a PSI rating, so check the rating on the hose and in the washer manual before fitting a splice to a washer hose. A hose with damage near a fitting, or a burst along its length, is better replaced.
What size barb splicer fits a hose?
Match the barb to the inside diameter of the hose. The kits here cover 3/16 in, 1/4 in, 5/16 in, 3/8 in, 1/2 in and 5/8 in, so measure the hose and pick the size that matches. A barb that is too small can slip, and a barb that is too large will not enter the hose.
How many clamps does a splice need?
A clamp on each end of the splice, over each barb end, tightened until snug. The Ailbiuko kit (on Amazon) carries 52 clamps and the KOOTANS kit (on Amazon) carries 46 clamps, so the box holds spares for more splices.
Can the same kit repair a garden hose?
Yes, for a clean cut. The listings state use for water, air, fuel, oil and natural gas hose, and a garden hose is a water hose. Size the barb to the garden hose in the same way, and check the repair for drips before putting the hose back to work. The water hose repair kit guide covers garden hose leaks in more detail.
How can the repair be checked?
Reconnect the hose, turn the water on, and look for drips at the joints. A joint that stays dry under water pressure is holding. A joint that drips needs the clamp tightened, or the barb reseated in the hose.




