How to Transport Riding Lawn Mower Safely
Load a riding mower onto a truck or trailer with the right ramp, a flat approach, and straps that hold it still for the trip.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Evcitn 75 in 1500 lb Truck Loading Ramps9.7/10View on Amazon - 2
VNN 29 in 1800 lb Shed Loading Ramps9.6/10View on Amazon - 3
VEVOR 1000 lb Folding Steel Ramps9.6/10View on Amazon - 4
MAXXHAUL 50872 Steel Ramp Top Kit9.5/10View on Amazon
To transport a riding mower, load it onto a truck bed or trailer with ramps rated above the mower weight, drive it up on flat ground, and strap it down so it cannot roll or shift on the trip. This guide shows how to transport riding lawn mower loads, from picking ramps to tying the mower down.
AcreMowerLab earns a commission when you shop through links here. It never changes your price. Affiliate disclosure.
| # | Product | Acre Score | Buy |
|---|---|---|---|
| 1 | Evcitn 75 in 1500 lb Truck Loading Ramps | 9.7/10 | Buy on Amazon |
| 2 | VNN 29 in 1800 lb Shed Loading Ramps | 9.6/10 | Buy on Amazon |
| 3 | VEVOR 1000 lb Folding Steel Ramps | 9.6/10 | Buy on Amazon |
| 4 | MAXXHAUL 50872 Steel Ramp Top Kit | 9.5/10 | Buy on Amazon |

Evcitn 75 in 1500 lb Truck Loading Ramps
Stainless steel truck ramps, 75 in long, with a 1500 lb pair capacity and a folding design for storage.
Who it's for: owners who load a riding mower into a truck bed or trailer and want long ramps for truck loading.
Who should skip it: anyone who needs a stated warranty.
The Evcitn pair runs 75 in long, with a 1500 lb capacity for the pair and a stainless steel build. It folds to 38.2 x 8.9 x 3.7 in, and the box holds work gloves, 2 tie-down straps and hazard tape. The listing does not state a warranty term or a slope angle.
Pros
- 75 in length suits truck beds and trailers
- Reinforced construction with professional welding
- Folds to 38.2 x 8.9 x 3.7 in for storage
- Work gloves, 2 tie-down straps and hazard tape in the box
Cons
- Warranty term is not stated on the listing
- 36.38 lb weight is heavier than the MAXXHAUL kit
- No slope angle is stated, so check the approach before loading
- The pair shares one 1500 lb capacity, so a mower near that limit leaves little margin

VNN 29 in 1800 lb Shed Loading Ramps
Alloy iron shed ramps in a 2 pack, with an 1800 lb capacity and a 12.7 degree tilt angle for shed and garage entries.
Who it's for: owners with a shed, barn or garage entry who want the stated 1800 lb capacity and a stated warranty.
Who should skip it: anyone loading into a truck bed, where the 29 in length makes for a short climb.
The VNN pair carries a stated capacity of 1800 lb, in alloy iron with a punched hole surface that grips and drains water. Each piece measures 29 in long, 24 in wide and 2 in high, with a 12.7 degree tilt angle, and the listing states a 1 year manufacturer warranty.
Pros
- 1800 lb stated capacity
- 1 year manufacturer warranty stated
- Punched hole surface grips and drains water
- Handle and pre-drilled holes with 3 screws for setup
Cons
- 29 in length suits low shed entries, not a truck bed
- The pair covers 48 in of width, so check the mower width before ordering
- No tie-down straps are listed in the box
- No carrying case is listed, only a handle

VEVOR 1000 lb Folding Steel Ramps
Steel folding ramps with a 1000 lb combined capacity, straps and a rubber handle for truck loading.
Who it's for: owners who want a folding steel pair with straps for truck loading.
Who should skip it: anyone whose mower needs more than the 1000 lb combined capacity.
The VEVOR pair is an all-steel set with a 1000 lb combined capacity and a white zinc-coated surface. It folds and unfolds within 1 second, with reinforced triangular joints and a rubber handle, and adjustable straps hold it to the truck edge. The listing does not state a warranty term.
Pros
- Folds and unfolds within 1 second
- Adjustable straps hold the ramps to the truck edge
- Rubber claw plates grip the truck edge
- White zinc-coated steel resists corrosion
Cons
- 1000 lb combined capacity is lower than the 1500 lb and 1800 lb options
- 37.04 lb weight is heavier than the Evcitn and MAXXHAUL options
- Warranty term is not stated on the listing
- No work gloves or hazard tape are included

MAXXHAUL 50872 Steel Ramp Top Kit
Steel ramp top kit that turns 2 x 8 in planks into loading ramps, rated at 700 lb per ramp.
Who it's for: owners who already have planks and want a light kit they can build up from planks.
Who should skip it: anyone who wants ramps ready out of the box.
The MAXXHAUL kit turns standard 2 x 8 in planks into ramps, with 2 steel ramp ends, 4 bolts, 4 nuts, 4 safety pins and 2 protective pads in the box. Each ramp supports up to 700 lb of distributed weight, and the powder-coated steel build resists rust.
Pros
- Turns 2 x 8 in planks of any length into ramps
- 700 lb per ramp of distributed weight
- Rubber pads protect the truck bed and trailer surface
- Safety pins and all hardware are in the box
Cons
- Planks are not included, so the ramps are not ready out of the box
- 700 lb per ramp is a distributed-weight rating, so check it against the mower weight
- Warranty term is not stated on the listing
- Plank length sets the slope, so a short plank makes a steep ramp
How to transport riding lawn mower: pick ramps rated for the load
Start with capacity: each listing states a load limit, per ramp or per pair, and the load on the ramps must stay below that stated limit. The options below state 700 lb per ramp, 1000 lb combined, 1500 lb per pair and 1800 lb, so match the stated rating to the mower, not to the truck. For the same bed height, a 75 in ramp also gives a gentler climb than a 29 in ramp.
| Ramp | Capacity | Length | Best for |
|---|---|---|---|
| Evcitn Truck Ramps | 1500 lb per pair | 75 in | Truck beds and trailers |
| VNN Shed Ramps | 1800 lb | 29 in per piece | Shed and garage entries |
| VEVOR Steel Ramps | 1000 lb combined | 75.98 in | Quick folding loads |
| MAXXHAUL Ramp Top Kit | 700 lb per ramp | Plank length | DIY ramps from planks |
See our aluminum vs steel mower ramps comparison and our best ATV truck ramps roundup before you choose.
Gear for loading a riding mower
The steps below need ramps that fit the mower and the truck bed, so the gear here is ranked by capacity, length and what comes in the box.
Step 1: measure the mower and the bed
Measure the mower width and the height of the truck bed or trailer deck before you buy ramps. The VNN pair covers 48 in of width when the 2 pieces sit side by side, each 24 in wide, while the Evcitn pair runs 75 in long. Check the fit on flat ground first.
Step 2: set the ramps on flat ground
Park the truck or trailer on flat ground with the parking brake set, then set the ramps against the bed or tailgate. The VEVOR ramps (on Amazon) grip the truck edge with rubber claw plates, and the adjustable straps hold them in place. The MAXXHAUL kit (on Amazon) has rubber pads under the ramp ends to protect the truck bed and help keep the plank ramps from sliding. Check that each ramp sits flat, with no gap under the ends.
Step 3: load the mower and strap it down
Drive the mower up the ramps at a slow, steady pace and stop once it sits fully on the bed or trailer deck. Put the mower in park, set the brake, and switch the engine off. Then strap the mower down with tie-down straps: the Evcitn pair comes with 2 tie-down straps in the box. Keep the VEVOR adjustable securing straps on the ramps, where they hold the ramps to the truck edge. Add wheel chocks for extra hold; see our wheel chocks safety guide for placement.
Safety
Never load a mower on ramps rated below the load they will carry: check the stated per-ramp or per-pair rating against the mower weight before you load, and use ramps long enough for the bed height. Wear the work gloves from the Evcitn box and keep children and pets out of the loading area.
FAQ: mowing large lots
What size ramp do I need for a riding mower?
Pick ramps rated above the mower weight. The VNN pair is rated to 1800 lb, the Evcitn pair to 1500 lb, the VEVOR pair to 1000 lb combined, and each MAXXHAUL ramp to 700 lb of distributed weight.
Can I load a riding mower with shed ramps?
Shed ramps suit low entries. The VNN ramps are 29 in long per piece with a 12.7 degree tilt angle, made for sheds, barns and garages. For a truck bed, the 75 in Evcitn ramps (on Amazon) give a longer, gentler climb.
Do I need straps to hold the ramps in place?
Straps help a lot. The VEVOR set has adjustable securing straps, the Evcitn pair comes with 2 tie-down straps, and the MAXXHAUL kit has safety pins for the ramp ends and rubber pads under them. Secure the ramps before you drive up.
How do I store loading ramps?
Fold them flat where they fit. The Evcitn pair folds to 38.2 x 8.9 x 3.7 in, and the VEVOR pair folds as well, with a rubber handle for carrying. The VNN ramps have a handle for moving them, and the MAXXHAUL kit breaks down to the ramp ends and hardware.
Can I build my own ramps from planks?
Yes, with a ramp top kit. The MAXXHAUL kit turns 2 x 8 in planks into ramps, with 2 steel ramp ends, 4 bolts, 4 nuts, 4 safety pins and 2 protective pads in the box. Each ramp supports up to 700 lb of distributed weight, and the plank length sets the slope.




