Outdoor Extension Cord Safety Cover: A Yard Guide
A box that keeps rain, snow, dust and dirt off an outdoor plug connection, matched to the cord gauge and plug size.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Flemoon 3 Pack Outdoor Extension Cord Safety Cover UL509.6/10View on Amazon - 2
cismorvex 3 Pack Outdoor Extension Cord Safety Cover IP549.6/10View on Amazon - 3
cismorvex 2 Pack Outdoor Extension Cord Safety Cover IP549.5/10View on Amazon
Rain finds every outdoor plug connection sooner or later. A cord that runs across a lawn to a mower, a pump or a string of holiday lights leaves the plug joint open to rain, snow, dust and dirt, and a wet joint can trip a breaker or cut power to the tool at the far end. An outdoor extension cord safety cover is a box that closes around the plug connection and keeps rain and dirt off it. This guide explains how the box works, how to match a cover to a cord, and where it belongs in the yard.
AcreMowerLab earns a commission when you shop through links here. It never changes your price. Affiliate disclosure.

Flemoon 3 Pack Outdoor Extension Cord Safety Cover UL50
A 3-pack of cord covers with UL50 and CSA marks, a 10 mm entry port for 14/16/18 gauge cords, and a snap-lock lid with 4 corner clips.
Who it's for: owners who want stated UL and CSA marks and a light box for a hanging connection.
Who should skip it: anyone with a 12 gauge cord, or anyone whose plug pair needs more than 2.0 x 2.0 x 5.3 inches inside.
The Flemoon cover is a 3-pack with the strongest safety marks here: UL50, UL50E and CSA C22.2 No. 94.1/94.2. Its outer size is 2.3 x 2.3 x 7.1 inches, its inner size 2.0 x 2.0 x 5.3 inches, and a 10 mm entry port seals 14/16/18 gauge cord, braided cable and flat wire. The lid closes with 4 corner clips and a snap-lock lid.
Pros
- UL50, UL50E and CSA C22.2 No. 94.1/94.2 marks stated
- 4 corner clips, snap-lock lid, gasket at each port
- 10 mm port seals 14/16/18 gauge cord, braided cable, flat wire
- Cable ties included for hanging through side mounting holes
Cons
- Port is sized for 14/16/18 gauge, so no 12 gauge cord
- No warranty term is stated on the listing
- Does not fit a power strip, right-angle plug or large adapter
- Smallest inner size here: 2.0 x 2.0 x 5.3 inches

cismorvex 3 Pack Outdoor Extension Cord Safety Cover IP54
A 3-pack of IP54 cord covers with 2 lockable latches, 2 cable clamps and room for 12/14/16 gauge cords.
Who it's for: owners with a 12 gauge cord or a plug pair that needs the wider inner size.
Who should skip it: anyone who needs a stated UL or CSA mark, or anyone whose plug is a right-angle plug or a large adapter.
The cismorvex 3-pack cover fits 12/14/16 gauge cords and standard grounded 3-prong and polarized 2-prong plugs, with an outer size of 2.51 x 3.2 x 7.32 inches and an inner size of 2.2 x 2.36 x 5.8 inches. The maker states an IP54 water resistant seal. It closes with 2 lockable latches, 2 cable clamps and rubber gaskets. The maker gives outer lengths of 7.32 and 7.7 inches; check before ordering.
Pros
- Fits 12/14/16 gauge cords, including 12 gauge
- 2 lockable latches, 50% fewer than 4-latch designs
- Hinged one-piece design, no assembly, no buckles to lose
- IP54 water resistant seal, gaskets and 2 cable clamps
Cons
- Not made for full submersion in water
- Larger than the Flemoon box: 2.51 x 3.2 x 7.32 inches
- May not fit a power strip, right-angle plug or large adapter
- No cable ties listed, so hanging takes a separate tie

cismorvex 2 Pack Outdoor Extension Cord Safety Cover IP54
A 2-pack of IP54 cord covers with 2 lockable latches, 2 cable clamps and room for 12/14/16 gauge cords.
Who it's for: owners who need a cover for 2 outdoor connections and want the 12 gauge fit.
Who should skip it: anyone who needs a stated UL or CSA mark, or anyone with more than 2 outdoor connections to cover.
The cismorvex 2-pack cover matches the 3-pack on gauge and seal: 12/14/16 gauge cords, 3-prong and 2-prong plugs, and an IP54 water resistant seal. Its outer size is 2.51 x 3.24 x 7.7 inches with an inner size of 2.28 x 2.32 x 5.8 inches, and the maker lists the weight as 0.49 pounds. The maker gives outer lengths of 7.7 and 7.36 inches; check before ordering.
Pros
- Fits 12/14/16 gauge cords, including 12 gauge
- 2 lockable latches, 50% fewer than 4-latch designs
- Hinged one-piece design, no assembly, no buckles to lose
- Gaskets, mounting holes and 2 clamps hold the cord in place
Cons
- Not made for full submersion in water
- No warranty term is stated on the listing
- May not fit a power strip, right-angle plug or large adapter
- Largest outer size here: 2.51 x 3.24 x 7.7 inches
How an outdoor extension cord safety cover works
The cover is a small plastic box. The plug connection sits inside the box, the cords leave through a port at each end, and the lid closes over the joint. Clips or latches hold the lid shut, rubber gaskets line the ports, and cable clamps grip each cord so a tug does not pull the plugs apart. The cismorvex covers state an IP54 water resistant seal, and the Flemoon cover states UL50, UL50E and CSA C22.2 No. 94.1/94.2 marks.
These covers suit any place where a cord joint sits outside: lawn and garden power tools, holiday lighting, pool pumps, patio heaters and cameras. The maker of the cismorvex covers states the box is not made for full submersion, so keep it out of standing water.
Fit is the part that matters most. A cover that is too small leaves the plug joint outside the seal, and a port that is too tight for the cord leaves the lid open. Match the cover to the cord gauge and the plug size.
Pick the right size for the cord and plug
Start with the cord gauge. The cismorvex covers fit 12/14/16 gauge cords, and the Flemoon cover fits 14/16/18 gauge cords through a 10 mm entry port. A 12 gauge cord needs the cismorvex size. The cismorvex covers suit 3-prong and 2-prong plugs. The Flemoon cover does not fit a power strip, a right-angle plug or a large adapter, and the cismorvex covers may not fit them either.
Then compare the inner size with the plug pair: 2.2 x 2.36 x 5.8 inches for the cismorvex 3-pack cover, 2.28 x 2.32 x 5.8 inches for the 2-pack cover, and 2.0 x 2.0 x 5.3 inches for the Flemoon cover. A plug pair wider than the inner width will not close inside the box, so measure the plugs before ordering.
Outdoor extension cord safety cover picks for the yard
The sizing step above is the step that needs the gear: pick the cover that matches the cord gauge and the plug pair in the yard.
How to fit and close a cover
Open the lid and lay the plug connection inside the box. Close the lid and fasten it shut: the cismorvex covers use 2 lockable latches, 50% fewer than the 4-latch designs the maker cites, and the Flemoon cover uses 4 corner clips with a snap-lock lid. Check that the rubber gaskets sit flat around each cord.
Hang the cover where the connection would otherwise lie on wet ground. The Flemoon cover comes with cable ties that pass through the side mounting holes, and the cismorvex covers have mounting holes of their own. Keep the box out of puddles and standing water. Do not use a cover on a damaged cord.
FAQ: mowing large lots
What does an outdoor extension cord safety cover do?
It closes a box around an outdoor plug connection so rain, snow, dust and dirt stay off the joint. Clips or latches hold the lid shut and cable clamps hold each cord in place.
What size cover fits a 12 gauge cord?
The cismorvex covers fit 12/14/16 gauge cords, while the Flemoon cover fits 14/16/18 gauge cords through a 10 mm entry port. A 12 gauge cord needs the cismorvex size.
Can a cord cover sit in a puddle?
Do not set any of these covers in standing water. The maker of the cismorvex covers states the box is not made for full submersion in water. Hang the cover or set it where water does not pool.
Do these covers fit a power strip?
No. The Flemoon cover does not fit a power strip, a right-angle plug or a large adapter, and the cismorvex covers may not fit them either.
How do you hang a cord cover?
Use the side mounting holes. The Flemoon cover comes with cable ties that pass through them, and the cismorvex covers have mounting holes of their own.




