Reel Mower Parts Diagram Explained
A reel mower parts diagram names each part and shows where it sits, so the right belt, chain, tire or spring can be matched before ordering.

On this page
A reel mower parts diagram is a labeled drawing of a reel mower that names each part and shows where it sits, so a worn belt, chain, tire or spring can be matched to the right replacement before ordering. The diagram starts at the cutting reel in the center and works outward to the rollers, the drive parts and the handle, with each part number printed beside its callout. Read it with the mower model in hand, match the part number first, then check the size figures, and the diagram turns a box of look-alike parts into a short, certain list.
As an Amazon Associate I earn from qualifying purchases. AcreMowerLab earns a commission when you shop through links here. It never changes your price. Affiliate disclosure.
Reel mower parts diagram: how to read it
Start at the cutting reel. The reel is the cylinder of spiral blades that spins against the bedknife to cut grass, and it sits between two side plates with a bearing retainer on each side. The right retainer and the left retainer hold the reel in place and set the reel-to-bedknife gap, so the diagram shows them as mirror parts with different part numbers. On a McLane front throw reel mower, the right retainer is part 1109 and the left retainer is part 1111. Note the side before ordering, since the two retainers are not interchangeable.
| Part | What it does | Fit and figures |
|---|---|---|
| Drive belt | Carries drive from the engine to the reel | McLane part 1060; 1/2 inch by 19.5 inches; fits 20 inch and 25 inch models |
| Engine chain | Carries drive from the engine | Tru-Cut part T11212; 40 chain, 26 links; fits C25 and C27 models |
| Reel chain | Drives the reel assembly | Tru-Cut part T11267; 40 chain, 22 links; fits C25 and C27 models |
| Drive wheel tires | Give the drive roller grip on the lawn | McLane part 1035; set of 5; 20 inch models need 5 tires, 25 inch models need 6 tires |
| Roller drive sprocket | Turns the rear roller | McLane part 1038; 30 tooth, 5 inches in diameter |
| Height adjustment spring | Holds the cutting height setting | McLane part 1100; fits 20 inch and 25 inch models |
| Reel bearing retainers | Hold the reel in place and set the reel gap | McLane parts 1109 right and 1111 left; fits 20 inch and 25 inch models |
The drive parts wear at different rates. A belt that slips or a chain that jumps usually points to the drive side of the diagram, while a reel that will not hold its gap points to the retainers. See the reel mower repair guide for the order of checks when a mower stops cutting cleanly.
Step 1: find the cutting reel and the rollers
Every reel mower parts diagram centers on the cutting reel, the roller at the front and the roller at the rear. The front roller sets the height of the cut with the rear roller, and the height adjustment spring holds that setting. On McLane front throw models the spring is part 1100, and it fits both the 20 inch and 25 inch mowers. Trace the line from the reel to the side plates, then to the retainers, before moving to the drive parts.
Step 2: follow the drive from the engine to the reel
The drive side of the diagram shows how power reaches the reel. On a McLane front throw mower the drive belt carries power from the engine to the reel, and the roller drive sprocket turns the rear roller. The McLane drive belt is part 1060 and measures 1/2 inch by 19.5 inches, and the roller drive sprocket is part 1038 with 30 teeth and a diameter of 5 inches. On Tru-Cut C25 and C27 models the engine chain is part T11212 with 40 chain and 26 links, while the reel chain is part T11267 with 40 chain and 22 links. Count the links on the old chain and compare them with the diagram before ordering, since the two chains share the same chain size and differ only in link count.
Step 3: count the drive wheel tires
The drive wheel tires sit on the drive roller and give it grip. McLane part 1035 is a set of 5 tires, and the count depends on the mower width: 20 inch models need 5 tires and 25 inch models need 6 tires, so check the width first and order the count the diagram lists for that width. A short count leaves a bare spot on the roller and the drive slips.
Step 4: match the part number, then the size
Part numbers come first. Two parts can look alike and still fit different mowers, so read the part number on the old part or on the model plate and match it to the diagram callout. McLane numbers to look for are 1060 for the drive belt, 1035 for the drive wheel tires, 1038 for the roller drive sprocket, 1100 for the height adjustment spring, and 1109 and 1111 for the right and left reel bearing retainers. Tru-Cut numbers are T11212 for the engine chain and T11267 for the reel chain. Once the number matches, check the size figures in the table above: belt width and length, chain size and link count, sprocket tooth count and diameter. A matching number with the wrong size still fits poorly, so check both.
What the diagram does not show
A parts diagram names parts and shows where they sit, but it does not show wear. A belt can look whole and still slip, a chain can look clean and still have stretched links, and a tire can look round and still have lost its tread. The diagram also does not show the order of removal, so follow the mower manual for the steps and keep the old parts beside the new ones until the job is done. For a mower that needs more than a single part, the manual reel mower picks and the reel mower roundup show the current range of reel mowers when repair no longer makes sense.
Safety
Wear eye protection and sturdy shoes, and clear sticks, stones and other debris from the work area before starting. Keep hands clear of the cutting reel and the chains, and keep children and pets out of the yard while the mower is apart. Work with the engine off and cool, and never reach near the reel while the mower can roll.
FAQ: mowing large lots
Where is the part number on a reel mower?
Look for the number stamped on the old part, on the model plate, or in the diagram callout. McLane belts, tires, sprockets, springs and retainers carry numbers such as 1060, 1035, 1038, 1100, 1109 and 1111, while Tru-Cut chains carry T11212 and T11267. Match the number first, then the size figures.
What size is the McLane reel mower drive belt?
The TURFPULSE replacement (on Amazon) for McLane part 1060 measures 1/2 inch by 19.5 inches and fits McLane 20 inch and 25 inch reel mowers. It is made of aramid tensile cords, natural rubber and fabric, and the maker lists a 1 year manufacturer warranty.
How many drive wheel tires does a McLane reel mower need?
It depends on the width: 20 inch models need 5 tires and 25 inch models need 6 tires. McLane part 1035 comes as a set of 5, so check the width on the mower before ordering.
What is the difference between the Tru-Cut engine chain and the reel chain?
Both are 40 chain for C25 and C27 models, but the engine chain, part T11212, has 26 links and the reel chain, part T11267, has 22 links. Count the links on the old chain before ordering, since the two chains look alike.
Where does the height adjustment spring sit on the diagram?
It sits beside the height adjustment parts near the front roller, where it holds the cutting height setting. On McLane front throw mowers it is part 1100 and fits 20 inch and 25 inch models. If the cutting height drifts after adjustment, the spring is the part to check first.
More mowing guides
- Best Manual Reel Mower (2026): 5 Top Picks Compared
- Reel Mower Repair: Common Fixes to Try
- Best Reel Mower (2026): 5 Picks Compared
- Hover Mower vs Reel Mower: Which One Should You Buy?
For more on keeping a reel mower cutting well, browse the mower maintenance guides.




