Bump Head vs Fixed Line Trimmer: Which One Should You Buy?
Bump feed heads and fixed line heads compared on line sizes, reloads, fit and upkeep, with 4 examples from the listings reviewed.
On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
AILEETE 25-2 Bump Feed Trimmer Head for Stihl FS Series9.5/10View on Amazon - 2
Weed Warrior PivoTrim Universal Fixed Line Trimmer Head9.5/10View on Amazon - 3
Weed Warrior Push-N-Load 2-Line Fixed Line Trimmer Head9.5/10View on Amazon - 4
490-040-C035 0.155" x 18.5" Pre-Cut Trimmer Line 18PKView on Amazon - 5
Universal Weed Eater HeadView on Amazon - 6
314608005 Trimmer Head for Ryobi Reel Easy+ Bump Feed StringView on Amazon - 7
Anleolife .095" Commercial Square String Trimmer Line forView on Amazon - 8
Anleolife .155" Commercial Square Heavy Duty Trimmer Line forView on Amazon - 9
Anleolife .095" 3-Layer Twisted String Trimmer Line for WeedsView on Amazon
Verdict: Choose a bump head if line should advance with a tap while trimming fences, beds and edges without stopping to wind a spool. Choose a fixed line trimmer head if precut line pushed straight into the head sounds simpler than any spool at all.
The bump head vs fixed line trimmer question comes down to how line leaves the head. A bump head feeds line from inside the head with a tap on the ground. A fixed line head keeps no coil: a short precut length goes in, cuts until it wears, then another length goes in. This comparison covers the feeding difference, then 4 examples from the listings reviewed.
AcreMowerLab earns a commission when you shop through links here. It never changes your price. Affiliate disclosure.
Weed Warrior Autowinder II Universal Bump Feed Trimmer Head
A universal bump feed trimmer head with a 16 inches cutting width and a 7000 rpm speed rating, holding up to 16 feet of line for trimming and edging grass.
Read the full review
The Autowinder II is a bump feed head built around a simple idea: tap the head on the ground and the line advances, so trimming along fences and beds keeps moving without stopping to wind a spool. The listing states a 16 inches cutting width, a 7000 rpm speed rating and room for up to 16 feet of 0.80, 0.095, 0.105 inch diameter line, with a 16 ounces weight in the spec table. Reloading without disassembling the entire head is the other practical point in its favour for long fence lines.
Pros
- Bump feed advances line with a simple tap, reducing downtime
- Reloads without disassembling the entire head
- Accepts 0.80, 0.095 and 0.105 inch diameter line
- Fits most gas brands and select cordless trimmers
Cons
- No line coil stated as included in the box
- Cutting width of 16 inches is fixed by the listing
- No warranty term is stated on the listing
- No safety certification is stated on the listing
Weed Warrior Push-N-Load 2-Line Fixed Line Trimmer Head
A fixed line trimmer head that takes precut line from 0.050 to 0.155 inch, with no spool winding and six precut 0.095-inch strips plus an adapter kit in the box.
Read the full review
The Push-N-Load is the fixed line answer to spool winding: push a precut strip into the head and keep trimming, with no spool to wind. The listing states a 0.050 to 0.155 inch line range, a 2-Line design in glass-filled nylon and a 13.6 ounces weight. The spec table lists gasoline-powered while the bullets describe a head for gas and battery powered trimmers, and the bullets carry the clearer fit claim here.
Pros
- No spool winding: push precut line directly into the head
- Wide line range from 0.050 to 0.155 inch
- Glass-filled nylon construction for abrasion resistance
- Six precut 0.095-inch strips and an adapter kit included
Cons
- Precut line must be carried and replaced as it wears
- Spec table lists gasoline-powered while the bullets say gas and battery powered
- No warranty term is stated on the listing
- No safety certification is stated on the listing
Quintillus H02 Universal Bump Feed Trimmer Head
A universal bump feed trimmer head in glass-filled nylon with 304 stainless steel hardware, a 7-pc hardware kit and a coil of 14Ft 0.095 line included.
Read the full review
The Quintillus H02 is a bump feed head that loads without opening the head: insert the line and crank the bump knob, then tap the head on the ground to extend the line. The listing states a glass-filled nylon head, 304 stainless steel hardware, a 7-pc hardware kit and a coil of 14Ft 0.095 line. The spec table contradicts itself on weight, listing 8 oz in one field and 1.98 pounds in another, so weight should be checked before buying for a long session.
Pros
- Loads without opening the head, by inserting line and cranking the bump knob
- Glass-filled nylon head with 304 stainless steel hardware
- 7-pc hardware kit covers a wide range of shafts
- Coil of 14Ft 0.095 line included in the box
Cons
- Spec table lists weight two ways: 8 oz and 1.98 pounds
- Fits trimmers that rotate counterclockwise only
- Line capacity is listed as a slash, not a figure
- No warranty term is stated on the listing
Kaberalty 0.11 Inch Pre-Cut Trimmer Line 24 Pack
A 24 Pack of pre-cut 0.11 inch trimmer line in 1.7FT lengths, made for the Craftsman 2-in-1 fixed line head on 2-cycle and 4-cycle trimmers.
Read the full review
The Kaberalty pack is not a head at all: it is replacement line for a fixed line head, and that distinction matters for this comparison. The listing states 0.11 inch pre-cut line in 1.7FT lengths, a 24 Pack quantity and a 3.52 ounces weight, with fit for the Craftsman 2-in-1 fixed line head on 2-cycle and 4-cycle trimmers. For a fixed line head already on the trimmer, pre-cut lengths remove measuring and cutting from each reload.
Pros
- Pre-measured and pre-cut line for quick reloads
- 24 Pack covers many reloads from a single pack
- Made for the Craftsman 2-in-1 fixed line head
- Fits most gas string trimmers using pre-cut 0.11 inch line
Cons
- Line only: no trimmer head is included
- Fits fixed line heads only, not bump feed heads
- No line diameter range beyond 0.11 inch
- No warranty term is stated on the listing
Other machines to compare
490-040-C035 0.155" x 18.5" Pre-Cut Trimmer Line 18PKCheck price on Amazon
Universal Weed Eater HeadCheck price on Amazon
314608005 Trimmer Head for Ryobi Reel Easy+ Bump Feed StringCheck price on Amazon
Anleolife .095" Commercial Square String Trimmer Line forCheck price on Amazon
Anleolife .155" Commercial Square Heavy Duty Trimmer Line forCheck price on Amazon
Anleolife .095" 3-Layer Twisted String Trimmer Line for WeedsCheck price on Amazon
Bump head vs fixed line trimmer side by side
| Factor | Bump head (Autowinder II) | Bump head (Quintillus H02) | Fixed line (Push-N-Load) | Fixed line (Kaberalty 24 Pack) |
|---|---|---|---|---|
| Feeding | Bump feed: tap the head on the ground to advance line | Bump feed: tap the head on the ground to extend line | Push-N-Load: push precut line directly into the head | Pre-cut line for a fixed line head, no head included |
| Line sizes | Up to 16 feet of 0.80, 0.095, 0.105 inch diameter line | Coil of 14Ft 0.095 line included | Accepts 0.050 to 0.155 inch line | 0.11 inch pre-cut line, 1.7FT lengths |
| Reload | Reload without disassembling the entire head | Load without opening the head, by inserting line and cranking the bump knob | No spool winding, insert precut line | Pre-measured and pre-cut line for quick reloads |
| Fit | Most gas brands and select cordless trimmers | Nearly all brands of gas and cordless trimmers that rotate counterclockwise | Gas and battery powered string trimmers | Craftsman 2-in-1 fixed line head on 2-cycle and 4-cycle trimmers |
| Weight stated | 16 ounces | Listed two ways in the spec table: 8 oz and 1.98 pounds | 13.6 ounces | 3.52 ounces for the line pack |
| In the box | Replacement bump head | Head, line coil and 7-pc hardware kit | Head, six precut 0.095-inch strips and adapter kit | 24 Pack replacement trimmer line |
Figures are manufacturer stated for the 4 example listings, collected 28 October 2026.
Feeding line: tap or push
A bump head advances line when the head taps the ground. The Autowinder II listing describes bump feed operation that advances line quickly and smoothly with a simple tap, helping reduce downtime while trimming grass and weeds. The Quintillus H02 listing describes the same motion: tap the head on the ground to extend the line after loading without opening the head.
A fixed line head skips the spool entirely. The Push-N-Load listing describes pushing precut line directly into the head for fast loading and replacement, with no spool winding. The Kaberalty listing describes pre-measured and pre-cut line for quick and convenient reloads on a fixed line head. The trade is simple: no winding, but each worn length must be swapped by hand.
Line sizes and reloads
Line size range separates the examples more than feeding style alone. The Autowinder II listing states room for up to 16 feet of 0.80, 0.095, 0.105 inch diameter line, and those are the sizes that head lists. The Push-N-Load listing states a stated range, accepting line from 0.050 to 0.155 inch, with six precut 0.095-inch strips in the box. The Quintillus H02 listing includes a coil of 14Ft 0.095 line, while the Kaberalty listing offers a single size: 0.11 inch pre-cut line in 1.7FT lengths. A head with a stated range accepts the sizes that range lists; a single-size pack suits a head that lists that size.
Reload speed also differs by design. Bump heads reload without full disassembly on the Autowinder II listing, and without opening the head on the Quintillus H02 listing. Fixed line heads reload by pushing in a fresh precut length, which is fast when precut stock is on hand.
What each head fits
Fit is where listings must be read closely, because a head that does not mount is no help at any line size. The Autowinder II listing states fit for most gas brands and select cordless string trimmer models. The Quintillus H02 listing states fit for nearly all brands of gas trimmers and cordless string trimmers that rotate counterclockwise, with a 7-pc hardware kit for the shaft. The Push-N-Load listing describes a universal replacement head for gas and battery powered string trimmers, though its spec table lists gasoline-powered alone. The Kaberalty listing is narrowest by design: it fits the Craftsman 2-in-1 fixed line head on 2-cycle and 4-cycle trimmers, plus most gas string trimmers using pre-cut 0.11 inch line.
Handling and upkeep
Weight and build shape how a head feels over a long session, but the listings state weight unevenly. The Autowinder II listing states 16 ounces, and the Push-N-Load listing states 13.6 ounces. The Quintillus H02 listing states weight two ways in its spec table, 8 oz and 1.98 pounds, so its true heft is unclear from the listing alone. The Kaberalty figure of 3.52 ounces covers a line pack, not a head, so it cannot be compared with head weights.
The 4 examples
Acreage and terrain fit
Autowinder II
Push-N-Load
Quintillus H02
Kaberalty 24 Pack
Matching It to Your Property
- Along fences and beds with many obstacles, a bump head that feeds line with a tap keeps trimming moving without a spool stop.
- On open lawn edges where reloads happen near the shed, a fixed line head with precut stock on hand reloads in moments.
- Where line sizes differ across the listings, match the line size to the size the head listing states.
- For storage, precut line packs stay separate from the head, while bump heads hold their line inside the head between sessions.
The Acre Score explained
The Acre Score weighs five factors: performance, build quality, value, safety and warranty. A factor the listing does not state scores zero, which is why all 4 examples score zero for safety and warranty.
| Product | Acre Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| Autowinder II | 9.5 | 30 | 21 | 21 | 0 | 0 |
| Push-N-Load | 9.5 | 29 | 21 | 20 | 0 | 0 |
| Quintillus H02 | 9.4 | 27 | 20 | 19 | 0 | 0 |
| Kaberalty 24 Pack | 9.2 | 23 | 16 | 18 | 0 | 0 |
Scores run from 9.2 to 9.8: each product’s point total is placed on that range, so more points always means a higher score.
For larger clearing work beyond trimming, see the brush and field mowers category for machines built for rough ground.
Wear eye and hearing protection, long pants and sturdy footwear, and keep bystanders well back while the line or blade spins. Clear stones and debris first, and stop the engine or remove the battery before clearing the head. Refuel only with the engine off and cool. See OSHA landscaping safety. Read our Safety Disclaimer.
FAQ: mowing large lots
What is a bump head on a string trimmer?
A bump head is a trimmer head that advances line when tapped on the ground. The Autowinder II and Quintillus H02 listings both describe bump feed operation, with line advancing on a tap so cutting length stays steady along fences and beds.
What is a fixed line trimmer head?
A fixed line head takes short precut lengths of line instead of a wound spool. The Push-N-Load listing describes pushing precut line directly into the head, and the Kaberalty listing describes pre-cut line made for a fixed line head.
Which line size should a fixed line head use?
Use the size the head listing states. The Push-N-Load listing accepts 0.050 to 0.155 inch line, while the Kaberalty line is 0.11 inch for a Craftsman 2-in-1 fixed line head. A size outside the stated range may not seat or cut as the maker intends.
Can a bump head fit a cordless trimmer?
Some can, but fit must be checked listing by listing. The Autowinder II listing states fit for most gas brands and select cordless models, and the Quintillus H02 listing states fit for gas and cordless trimmers that rotate counterclockwise.
Does a fixed line head need a spool?
No. A fixed line head uses precut lengths, so there is no spool to wind. The trade is carrying enough precut stock, since each length is replaced by hand once it wears.
