Chainsaw Chain Sharpening Guide: How to File a Chain by Hand
A step-by-step chainsaw chain sharpening guide for matching the file to the chain, setting the angle, and filing each cutter by hand.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Oregon Chainsaw Chain Sharpening Kit with Hard Case9.6/10View on Amazon - 2
Oregon CS1500 Self-Sharpening Electric Chain Saw9.7/10View on Amazon - 3
Oregon Universal Chainsaw Field Sharpening Kit9.5/10View on Amazon
A dull chain turns cutting into pushing, and the saw throws fine dust instead of chips. A chainsaw chain sharpening guide starts with that sign: when the cutters stop biting, the chain needs filing, not forcing. This guide walks through the job in order, from matching the file to the chain pitch to checking the depth gauges, so the chain cuts cleanly again.
AcreMowerLab earns a commission when you shop through links here. It never changes your price. Affiliate disclosure.
Chainsaw chain sharpening guide: match the file to the chain
A round file must match the chain pitch, and the pitch is stamped on the chain or listed in the saw manual. A file that is too small sits low in the cutter and rounds the edge, while a file that is too large rides high and misses the cutting corner. The table below pairs the common round file sizes with the chain pitches the listings state, and a universal file set roundup lists kits that carry the full range.
| Round file | Chain pitch | Use |
|---|---|---|
| 5/32 inch | 1/4 inch | Small chains and pole saws |
| 3/16 inch | 0.325 inch | Mid-size chains |
| 7/32 inch | 3/8 inch | Full-size chains |
| 1/8 inch, 11/64 inch and 13/64 inch | Other pitches | Other chain pitches the kits list as compatible |
Kits on the listings carry round files from 1/8 inch to 13/64 inch, so one kit covers the pitches the Hipa listing states as compatible, from 1/4 inch to 1/2 inch. The Hipa kit (on Amazon) lists 12 pieces with 6 round files in 5/32 inch, 3/16 inch, 7/32 inch, 1/8 inch, 11/64 inch and 13/64 inch, plus a 6 inch flat file and a depth gauge. The Morrowind set lists 5 round files in five of those sizes, with no 13/64 inch file, while the MeasuPro kit (on Amazon) lists 7 pieces with 3 round files, a 6 inch flat file, a handle, a filing guide and a pouch. Check the chain pitch before buying, and keep the size marks on the files visible so the right file is easy to find.
Step 2: clean the chain and bar
Start with the saw switched off and the chain brake set, then brush the chain and the bar groove clear of chips and oil. A bar groove cleaner clears the channel and the oil holes, and a clean bar lets the chain run true while filing. For storage after the job, a chainsaw bar cover keeps the cutters covered and the bar protected.
Step 3: set the filing angle
Clip the file guide onto the bar and set the angle the chain calls for. The UF-Sharp set lists a file guide with angles of 10, 25, 30 and 35 degrees, and the guide holds the file at the same angle on each cutter. Hold the file level and steady, and check the angle before the first stroke so the cutters stay even around the chain.
Step 4: file the cutters
File from the inside of each cutter outward, pushing forward only and lifting the file on the return stroke. Give each cutter the same strokes, and mark the starting cutter so the chain is filed all the way around without missing one. Work the cutters on one side of the chain, then turn the saw around and file the cutters on the other side, using the same angle setting mirrored for the cutters facing the other way.
Step 5: lower the depth gauges
After the cutters, lay the depth gauge tool over the chain and check each raker against it. The Hipa and UF-Sharp listings state a 2-in-1 depth gauge with .025 inch and .030 inch settings, used with a 6 inch flat file to bring the rakers down to the right height. A chainsaw length gauge checks cutter tooth length, which is a separate check from raker height.
Pick a steady work spot
Clamp the bar in a vise or hold the saw steady on a bench so the chain does not move while filing. Good light matters, because the cutter edge is small and the file marks are hard to see in shadow. Lay the kit out in order, file sizes in a row, so the right file is at hand without digging through the pouch.
Know when the chain needs filing
A chain that throws dust, pulls to one side, or needs pushing through the cut is asking for the file. Filing little and often keeps the cutters even and saves steel, while waiting until the chain is badly dull means more filing on each cutter. Check the chain each time the saw is fueled, and file before the cutters are rounded over.
Keep the kit together
A sharpening kit is only useful when it is all in one place, so keep the files, the flat file, the gauge and the handle in the pouch the kit came with. Kits range from a 5-piece set to a 13-piece set, and the larger kits add a quick check gauge, a bar groove cleaner and extra file sizes. The Kakei kit lists 8 packs with 3 round files, a 6 inch flat file, a depth gauge tool, a filing guide, a wood handle and a travel pouch. A chainsaw tool kit roundup covers the wider kits, and the trimmers and blowers section lists more guides for cutting tools.
Safety
Switch the saw off and set the chain brake before touching the chain, and wear gloves and eye protection while filing. Keep fingers clear of the cutters, and hold the file by its handle so the tang cannot slip into the hand. Work away from other people and pets, and keep the chain covered when the saw is carried or stored. Refuel only with the engine off and cool.
FAQ: mowing large lots
Can you sharpen a chainsaw chain by hand?
Yes. A round file matched to the chain pitch, a file guide, and a flat file for the depth gauges are enough to sharpen a chain by hand.
How do you file a chainsaw chain with a file guide?
Set the guide on the bar at the angle the chain calls for, hold the file level in the guide, and push forward through each cutter, lifting on the return. File each cutter with the same strokes, then turn the saw around and file the other side, using the same angle setting mirrored for the cutters facing the other way.
What size file fits the chain?
Match the file to the chain pitch: a 5/32 inch file fits a 1/4 inch pitch chain, a 3/16 inch file fits a 0.325 inch pitch chain, and a 7/32 inch file fits a 3/8 inch pitch chain. Kits also carry 1/8 inch, 11/64 inch and 13/64 inch files for other chain pitches.
How often should a chainsaw chain be sharpened?
As often as the cutting tells you it needs it. File when the saw throws dust, pulls to one side, or needs pushing through the cut, and check the chain each time the saw is fueled.
What does the depth gauge do?
The depth gauge sets how far each raker sits below the cutter edge, which sets how deep each cutter bites. The listings state .025 inch and .030 inch settings, checked with a 6 inch flat file after the cutters are filed.
More mowing guides
- Best Chainsaw File Set Universal Kit (2026)
- Best Chainsaw Tool Kit (2026): 5 Picks Compared
- Best Chainsaw Bar Cover (2026): 5 Picks for Storage and Transport
- Best Chainsaw Chain for Dirty Wood (2026)
See the trimmers and blowers section for more guides on cutting tools.




