Repair Ends for Garden Hose: How to Fit a New End
How to repair a garden hose end with a replacement fitting, from matching the hose size to tightening the clamp and checking for leaks.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
BILAL Garden Hose Repair Connector Kit, 5 Sets, Fits 3/4 or 5/8 in Hose9.6/10View on Amazon - 2
Hourleey Garden Hose Repair Connector with Clamps, 5 Sets, Fits 3/4 or 5/8 in Hose9.6/10View on Amazon - 3
SIGURANTA 5/8 in Brass Garden Hose Repair Kit, 2 Sets, Male and Female9.6/10View on Amazon - 4
AuySier Garden Hose Repair Kit, 3 Sets, Fits 3/4 and 5/8 in Hose9.6/10View on Amazon
When the hose end splits on a property where the hose runs from the tap to the beds and the wash pad, repair ends for garden hose are the replacement fittings that put a new end on the damaged hose. This guide shows how to match the fitting to the hose, cut the damaged end and tighten the clamp. The kits below cover aluminum and brass ends for the common hose sizes, and each one handles a different part of the job.
AcreMowerLab earns a commission when you shop through links here. It never changes your price. Affiliate disclosure.

BILAL Garden Hose Repair Connector Kit, 5 Sets, Fits 3/4 or 5/8 in Hose
A 5-set aluminum hose repair kit with stainless steel clamps for 3/4 or 5/8 inch hose, with 10 clamps and an extra rubber gasket.
Who it's for: owners who want 5 spare ends in aluminum for 3/4 or 5/8 inch hose.
Who should skip it: anyone with a 1/2 inch hose, or anyone who wants brass fittings.
BILAL lists a 5-set garden hose repair kit with 5 female and 5 male connectors and 10 clamps, plus an extra rubber gasket, for 3/4 or 5/8 inch hose fittings. The connectors are high quality aluminum with corrosion resistance, and the clamps are stainless steel. The maker states to keep the cut flat and tighten the stainless clamps as tightly as possible for a tight, no-leak connection, and to choose the correct hose size before ordering. The kit also fixes leaks in the middle of a hose, as long as the size is right.
Pros
- Fits both 3/4 and 5/8 inch hose fittings
- 5 sets of male and female connectors with 10 stainless steel clamps
- Aluminum connectors resist corrosion
- Extra rubber gasket included for a spare seal
Cons
- No warranty term is stated
- Aluminum connectors rather than brass
- Only one extra rubber gasket is stated
- No stated fit for 1/2 inch hose

Hourleey Garden Hose Repair Connector with Clamps, 5 Sets, Fits 3/4 or 5/8 in Hose
A 5-set aluminum hose repair kit with stainless steel clamps for 3/4 or 5/8 inch hose, with 5 extra rubber washers and no tools needed.
Who it's for: owners who want 5 spare ends that fit without tools.
Who should skip it: anyone with a 1/2 inch hose, or anyone who wants brass fittings.
Hourleey lists a 5-set garden hose repair kit with male and female connectors and clamps, plus 5 extra durable rubber washers, for 3/4 or 5/8 inch hose fittings. The connectors are high-quality aluminum and the clamps are rust-resistant stainless steel. The maker states the kit installs without tools and creates a tight seal to eliminate water leakage. Inside the listing, the title and bullets state 5 sets while the spec table counts 1 item; the title and bullets carry the count.
Pros
- Fits both 3/4 and 5/8 inch hose fittings
- 5 sets of male and female connectors with 5 extra rubber washers
- Installs without tools, per the listing
- Aluminum connectors with rust-resistant stainless steel clamps
Cons
- No warranty term is stated
- Aluminum connectors rather than brass
- No stated fit for 1/2 inch hose

SIGURANTA 5/8 in Brass Garden Hose Repair Kit, 2 Sets, Male and Female
A 2-set brass hose repair kit with 304 stainless steel clamps for 5/8 inch hose, with a 15.95 mm barb and 3/4 inch threaded ends.
Who it's for: owners who want brass fittings for a 5/8 inch hose that feeds a sprayer or a pressure washer.
Who should skip it: anyone with a 3/4 inch hose, or anyone who wants 5 sets in one pack.
SIGURANTA lists a 2-set brass garden hose repair kit with 2 male and 2 female connectors, 4 stainless tightening clamps and 2 extra washers, for standard 5/8 inch hose. The connectors are 58-3 brass, rustproof and corrosion resistant, and the clamps are 304 stainless steel. The barb size is 15.95 mm (0.628 in), and the kit works with standard 3/4 inch threaded ends for garden hose, sprayers and nozzles. The maker states the fittings serve as replacement ends for damaged hoses and work with sprinkler systems and pressure washers.
Pros
- 58-3 brass connectors, rustproof and corrosion resistant
- 304 stainless steel clamps
- Barb size 15.95 mm (0.628 in) for standard 5/8 inch hose, with 3/4 inch threaded ends
- Works with garden hoses, sprinkler systems and pressure washers
Cons
- No warranty term is stated
- Only 2 sets, the smallest count in this group
- Barb fits 5/8 inch hose only; the 3/4 inch figure is the thread, not the hose
- Only 2 extra washers are stated

AuySier Garden Hose Repair Kit, 3 Sets, Fits 3/4 and 5/8 in Hose
A 3-set aluminum hose repair kit with zinc alloy clamps for 3/4 and 5/8 inch hose, with 6 extra rubber washers.
Who it's for: owners who want 3 spare ends with extra washers for 3/4 or 5/8 inch hose.
Who should skip it: anyone who wants stainless steel clamps, or 5 sets in one pack.
AuySier lists a 3-set garden hose repair kit with 3 female and 3 male connectors and zinc alloy clamps, plus 6 extra rubber washers, for 3/4 and 5/8 inch hose. The connectors are aluminum alloy with stainless steel screws, for long-lasting performance and rust resistance. The maker states a tight, no-leak connection that prevents water wastage. Inside the listing, the spec table Size lists 3/4 inch while the title and bullets state fit for 3/4 and 5/8 inch hose; the title and bullets carry the fit.
Pros
- Fits both 3/4 and 5/8 inch hose
- 3 sets of male and female connectors with zinc alloy clamps
- 6 extra rubber washers included
- Aluminum alloy connectors with stainless steel screws
Cons
- No warranty term is stated
- Zinc alloy clamps rather than stainless steel clamps
- Only 3 sets, fewer than the 5-set kits
Repair ends for garden hose: the short answer
Match the fitting to the hose size first. The kits here fit 3/4 or 5/8 inch hose, except the SIGURANTA kit (on Amazon), which fits 5/8 inch hose with 3/4 inch threaded ends. Cut off the damaged end, keep the cut flat, push the fitting onto the hose and tighten the clamp. The BILAL listing states to tighten the stainless clamps as tightly as possible. A tight, no-leak connection is the result to check for when the water goes back on. For quick connects that thread onto a repaired end, see the best water hose quick connect for pressure washer picks.
Hose repair kits for the job
These repair kits cover the sizes and materials a damaged hose end needs, and each one handles a different part of the job: fitting the hose, sealing the joint, or stocking spares.
Step 1: match the fitting to the hose
Check the hose size before ordering, as the BILAL listing advises. The BILAL, Hourleey and AuySier kits fit 3/4 (on Amazon) or 5/8 inch hose, while the SIGURANTA kit fits 5/8 inch hose with a barb of 15.95 mm (0.628 in) and standard 3/4 inch threaded ends. A fitting that matches the hose slides on and seals; the wrong size either will not slide on or will not seal. Order the kit that states the size.
| Kit | Fits | Sets | Connectors | Clamps |
|---|---|---|---|---|
| BILAL Hose Repair Kit | 3/4 or 5/8 in | 5 | Aluminum | Stainless steel |
| Hourleey Repair Kit | 3/4 or 5/8 in | 5 | Aluminum | Stainless steel |
| SIGURANTA Brass Kit | 5/8 in hose, 3/4 in thread | 2 | 58-3 brass | 304 stainless steel |
| AuySier Repair Kit | 3/4 and 5/8 in | 3 | Aluminum alloy | Zinc alloy |
Step 2: cut the damaged end and keep the cut flat
Cut off the damaged end of the hose so the fitting meets sound hose. Keep the cut flat, as the BILAL listing advises, so the fitting seats squarely and the clamp can close evenly around it. A ragged or angled cut leaves a gap the clamp cannot close. Turn the water off and let the hose drain before cutting, so the work area stays dry.
Step 3: fit the end and tighten the clamp
Push the fitting onto the hose end and tighten the clamp. The BILAL listing states to tighten the stainless clamps as tightly as possible, and the Hourleey listing states its kit installs without tools. Fit the male or female end to match the tap or the accessory it will join: each kit holds both male and female connectors. For quick connects that thread onto a repaired end, see the best water hose quick connect kit picks.
Step 4: check for leaks
Turn the water back on slowly and watch the repaired joint. A tight, no-leak connection holds without drips at the clamp and the fitting. If water shows at the joint, turn the water off, tighten the clamp further and check again. A spare washer or gasket from the kit can replace a worn one in the fitting’s threaded end: the BILAL kit holds an extra rubber gasket, the Hourleey kit holds 5 extra rubber washers, the SIGURANTA kit holds 2 extra washers and the AuySier kit holds 6 extra rubber washers.
Repair a cut in the middle of the hose
A repair connector also fixes a leak in the middle of a hose, not only a damaged end. The BILAL listing states the connector works for fixing leaks in the middle of a hose, as long as the size is right. Cut out the damaged section, keep both cuts flat, and join both hose ends with a male and a female connector from the kit. The same clamp-and-check steps apply.
Safety
Turn the water off and let the hose drain before cutting, and keep the cut end pointed away from people when the water goes back on. Wear eye protection when cutting the hose, and keep children and pets away from the work area. Never point a pressurized hose or a pressure washer at people or animals. Check the repaired joint for leaks before putting the hose back to full use.
FAQ: mowing large lots
What size hose repair fitting fits a garden hose?
Match the fitting to the hose: the BILAL, Hourleey and AuySier kits fit 3/4 or 5/8 inch hose, while the SIGURANTA kit fits 5/8 inch hose with 3/4 inch threaded ends. Choose the correct hose size before ordering, as the BILAL listing advises.
How to repair a garden hose end?
Cut off the damaged end and keep the cut flat, push the fitting onto the hose, and tighten the clamp. Turn the water back on slowly and check the joint for leaks.
Can a cut in the middle of a garden hose be repaired?
Yes. The BILAL listing states the connector fixes leaks in the middle of a hose, as long as the size is right. Cut out the damaged section and join both ends with a male and a female connector from the kit.
Are tools needed to fit a hose repair connector?
The Hourleey kit installs without tools, per the listing. The other kits tighten with their clamps; the BILAL listing states to tighten the stainless clamps as tightly as possible.
Will a hose repair fitting work with a pressure washer?
The SIGURANTA listing states its fittings work with pressure washers, as well as garden hoses, sprinkler systems and watering accessories. Match the fitting to the hose size first.




