Robotic Lawn Mower Installation: A Step-by-Step Guide
Robotic lawn mower installation in plain steps: walk the lawn, lay the boundary wire, place the charging station and run the first mow.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Husqvarna Automower 550 Robotic Lawn Mower9.7/10View on Amazon - 2
roborock RockMow X130H Robot Lawn Mower9.6/10View on Amazon - 3
DREAME Robot Lawn Mower Decal for A3 AWD Series9.5/10View on Amazon
A lawn that runs past the back fence, around the trees and down toward the ditch is the kind of ground a robotic mower is made for, once the setup is done. The mower only earns its keep when the boundary is right and the charging station is set, so robotic lawn mower installation is the work that decides whether the mower covers the lawn or wanders off it. This guide walks through it step by step, from the first walk around the lawn to the first mow.
AcreMowerLab earns a commission when you shop through links here. It never changes your price. Affiliate disclosure.
Robotic lawn mower installation: walk the lawn first
Start on foot, before any wire comes out of the box. Walk the whole mowing area and note every tree, bed, path, patio edge, pond and narrow passage. The boundary wire marks where the mower may go, so the walk decides the shape of the wire. Mark the places the mower must stay out of, such as flower beds, the vegetable patch, the patio and any pond edge, and note where the lawn narrows between the house and a fence. A mower that has to squeeze through a tight gap will spend its time turning instead of cutting, so give the wire a clear run where you can.
The wire comes in kits sized by length. Pick the kit that covers the edge of the mowing area with wire to spare for joins and repairs:
| Kit | Wire length | In the kit |
|---|---|---|
| Husqvarna boundary wire | 50m | Wire for Automower installation, also a guide wire |
| WORX WA0184 kit | 165 feet | 18 AWG extension wire for a larger lawn |
| FOTEEMO kit | 100m/328ft | 50 ground spikes, 10 cable connectors, 20 sets of connection terminal |
| Headley Tools kit | 150m/492ft | 50 pegs, 10 wire connectors, 9 titanium blades |
| FOTEEMO kit | 200m/656ft | 50 pegs, 10 cable connectors, 20 sets of connection terminal |
| Husqvarna heavy-duty spool | 1640 ft/500m | 3.4mm wire with a 100% copper core |
See the robotic lawn mower maintenance guide for what to do once the mower is running.
Step 2: place the charging station
Set the charging station on flat ground near an outdoor outlet, with a clear run of lawn in front of it so the mower can drive straight in to dock. Keep it out of the way of foot traffic and away from beds the mower must avoid, and give it shade from the afternoon sun where you can. The station is the mower’s home base, so place it on the boundary wire where the mower can follow the wire home to it.
Step 3: lay the boundary wire
Lay the wire around the edge of the mowing area, with a loop around each bed, tree and obstacle the mower must avoid. Peg it to the ground with the pegs from the kit so it sits tight against the soil and the mower passes over it cleanly. The wire works as an invisible fence: the mower reads the signal and turns back inside the boundary.
The wire in the FOTEEMO and Headley Tools kits is 2.7 mm thick, made of 24 strands of tinned copper-clad aluminum, and the Husqvarna heavy-duty wire is 3.4mm with a 100% copper core. Join lengths with the cable connectors from the kit, and keep a few connectors spare for repairs. Where the wire has to cross a path, bury it under the path surface so foot traffic and the mower do not wear through it.
Step 4: connect the wire and charge the mower
Connect the two ends of the boundary wire to the charging station, then plug the station in and let the mower charge. Check that the station shows the wire loop is connected before the first run, and follow the manual for the signal check. A loop with a break will not hold the mower inside the boundary, so walk the wire once more and look for a peg that has lifted or a length that has gone slack.
Step 5: run the first mow and adjust the wire
Send the mower out and watch the first run from the edge of the lawn. Where it misses a strip, move the wire out a little; where it strays toward a bed, pull the wire in. If the wire gets cut, splice it with a coupler: the Husqvarna coupler joins and repairs a cut boundary wire, and the kits carry 10 cable connectors for the same job. Once the mower covers the whole lawn and stays inside the boundary, the installation is done.
Mind the weather and the ground
The wire is made to sit outside. The Headley Tools wire (on Amazon) is weatherproof and resists moisture and frost, and the FOTEEMO wire is built to stand up to rain, sunlight, snow and ice. Pegs hold the wire down through the season, and the grass grows over it in time so it sits out of sight. On wet ground, wait for a dry day to peg the wire, since soft ground will not hold a peg as well as firm ground.
Safety
Keep children and pets out of the yard while the mower runs, and clear sticks, stones and toys from the lawn before the first mow. Keep hands clear of the blades when the mower is running, and follow the manual for blade changes. The mower carries small, sharp blades, so treat it like any other mower when you lift it or work on it.
FAQ: mowing large lots
How much boundary wire do I need?
Measure the edge of the mowing area, including the loops around beds and trees, then pick a kit that covers it: 50m, 100m/328ft, 150m/492ft, 200m/656ft and 1640 ft/500m spools are listed, and the WORX kit (on Amazon) adds 165 feet of 18 AWG wire to extend a lawn that needs more.
What is boundary wire made of?
The FOTEEMO and Headley Tools wire is 24 strands of tinned copper-clad aluminum, 2.7 mm thick, with the inner diameter at 1.17 mm on the FOTEEMO wire. The Husqvarna heavy-duty wire is 3.4mm with a 100% copper core.
Can I extend the boundary wire later?
Yes. The WORX kit adds 165 feet of 18 AWG wire to extend the mowing area, and the kits carry 10 cable connectors for joins. A cut wire can be spliced with the Husqvarna coupler, which comes as a 5 piece set.
What if the mower crosses the boundary wire?
Check the wire first: a peg may have lifted, or the wire may be cut. Peg the wire back down, and splice a cut with a coupler or a cable connector. The wire works as an invisible fence, and a strong signal keeps the mower inside the area it marks.
Does the boundary wire survive winter?
The Headley Tools wire is weatherproof and resists moisture and frost, and the FOTEEMO wire is built to stand up to rain, sunlight, snow and ice. The wire stays in the ground through the cold months; the mower manual covers winter storage.




