Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Rotary Hoe Parts: Common Replacements to Know

Worn tines, tired hardware and hub holders are the rotary hoe parts to check first, and matching them to the tiller is a matter of size, hole pattern and fitment.

Rotary Hoe Parts: Common Replacements to Know
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Walensee Action Hoe with Adjustable 36-66 Inch HandleWalensee Action Hoe with Adjustable 36-66 Inch Handle9.6/10View on Amazon
  2. 2Altdorff Rotary Cultivator with Detachable TinesAltdorff Rotary Cultivator with Detachable Tines9.6/10View on Amazon
  3. 3Lilyvane Garden Hoe for Weeding with 60 Inch HandleLilyvane Garden Hoe for Weeding with 60 Inch Handle9.6/10View on Amazon

A rear-tine tiller that stops biting into hard ground usually has worn tines. The tines do the digging, and they wear down through soil, roots and stones. Rotary hoe parts are the replacement tines, hardware and hub holders that bring a tiller back to its original bite. This guide names the parts that wear out, shows how to match them to a tiller, and explains what to check before ordering.

AcreMowerLab earns a commission when you shop through links here. It never changes your price. Affiliate disclosure.

Rotary hoe parts: the replacements to know first

The rotary hoe parts in this guide fall into a short list: tines, mounting hardware and hub holders. Tines cut the soil and wear down with use, hardware holds the tines to the hub, and hub holders carry the tines on the tine shaft.

Part What it does When to replace it
Bolo tines Cut into soil and pull the tiller forward When the edges round off and the tiller stops biting into hard ground
Cap screws, hex nuts and lock washers Hold each tine to the hub When threads or washers show wear
Cast iron hub holders Carry the tines on the tine shaft When a holder cracks or the bolt holes wear out of round

For the jobs a rotary hoe handles around the property, see the guide to rotary hoe uses. The tillers and cultivators hub lists the full set of tiller guides on this site.

Step 1: match the tine to your tiller

Start with the tine itself. A complete 16-piece set for a Troy-Bilt Horse or Pony rear-tine tiller holds 8 left-hand and 8 right-hand bolo tines, enough to rebuild both sides of the tine shaft. Each bolo tine is 12 inches long with a 7/16 inch mounting hole, and the three holes are spaced 2-5/8 or 3-1/8 inches center to center, so match the hole pattern on the old tines first.

Smaller sets follow the same pattern. The Hicarer 12-piece (on Amazon) set holds 6 left-hand and 6 right-hand tines with 36 screws and nuts, and the Hicarer tines measure 1.25 inches wide and 11 inches long, with bolt hole spacings of 0.75, 3.25 and 3.9 inches to the center. King Kutter TG and TG-G tine blades run 9/32 inch thick, 2-9/16 inches wide and 7-4/5 inches long tip to tip, with M14-1.5X35 hex cap screws. Match the part number as well as the size: the 1901118 set replaces Troy-Bilt and MTD part numbers 1901118, 10802, 129259, 129359, 1569, 1570 and 370-270, while the Stens 370-350 (on Amazon) set and the Rotary 8620 (on Amazon) set fit the same Horse and Pony tillers.

Fitment goes by model, not by tine shape alone. The Maxpower 12703 set fits Troy-Bilt Bronco, Pro-Line and Tuffy models from 2005 and up, uses 2 mounting holes, and replaces part numbers 742-04116-0637 and 742-04117-0637. The M MATI 06722-V20-003 kit (on Amazon) fits Honda FRC800 and FRC800K1 tillers and replaces part numbers 72461-V20-003 and 72465-V20-003. Check the fitment detail before ordering.

Step 2: count the hardware before you order

A tine change needs hardware as well as tines. The 16-piece 1901118 set includes 32 cap screws, 32 hex nuts and 32 lock washers in the box, so nothing is left to hunt for partway through the change. The 12-piece Hicarer set includes 36 screws and nuts. Count the hardware against the tine count: a set with 8 left-hand and 8 right-hand tines needs hardware for each tine on each side of the shaft.

Step 3: check the hub holders and the tine shaft

The hub holders carry the tines, and they wear too. The Reliable Aftermarket Parts 1901118 (on Amazon) set includes the cast iron hub holders, so the set bolts up complete. Look at the bolt holes on the old holders: holes worn out of round will not hold a tine tight, even with new hardware. If a holder is cracked, replace the holder with the tines rather than bolting new tines to a worn holder.

Know the sizes on the shelf

Tine sizes vary by machine, so read the size before ordering. The Troy-Bilt Horse and Pony bolo tine is 12 inches long with a 7/16 inch mounting hole. The Hicarer tine is 1.25 inches wide and 11 inches long. The King Kutter tine blade is 9/32 inch thick, 2-9/16 inches wide and 7-4/5 inches long tip to tip. A 42-piece King Kutter set holds 21 right-hand and 21 left-hand blades.

Depth follows the tine and the ground. With sharp Hicarer tines, deep tilling runs 9-10 inches and shallow tilling runs 3 inches, which prepares a fine seedbed. Worn and rounded tines stop biting into hard ground, and a fresh set brings back the original tilling depth and forward pull.

Safety

Call the utility locator before digging in new ground, and mark the lines before the tines go in. Wear eye protection and sturdy shoes, and keep hands and feet clear of the tines while the tiller is running. Change tines with the engine off and cool, and keep children and pets out of the work area. Clear stones, roots and debris from the bed before tilling so the tines do not throw them.

FAQ: mowing large lots

What shows that tiller tines are worn out?

Worn and rounded tines stop biting into hard ground. When the tiller rides over the surface instead of digging in, or the forward pull fades, the tines are worn. A fresh set brings back the original tilling depth and forward pull.

What size tines fit a Troy-Bilt Horse tiller?

The 1901118 set fits the Horse and Pony with 12 inch bolo tines, a 7/16 inch mounting hole, and holes spaced 2-5/8 or 3-1/8 inches center to center. Match the hole pattern on the old tines first, and check the part number against 1901118, 10802, 129259, 129359, 1569, 1570 or 370-270.

Do replacement tine sets include the hardware?

The 16-piece 1901118 set includes 32 cap screws, 32 hex nuts and 32 lock washers, and the 12-piece Hicarer set includes 36 screws and nuts. Count the hardware in the box before ordering, and keep the old bolts as a pattern to match.

What is a bolo tine?

A bolo tine is the digging tine used on rear-tine tillers. The 1901118 set uses 12 inch bolo tines, with 8 left-hand and 8 right-hand tines to rebuild both sides of the tine shaft.

How deep can a rotary hoe till?

With sharp Hicarer tines, deep tilling runs 9-10 inches and shallow tilling runs 3 inches. The depth also depends on the ground: hard or rocky soil holds the tines up, while soft garden soil lets them dig in.

More mowing guides

More buying guides

Tillers and Cultivators ·

Rotary Hoe Uses: What It Does Best

A rotary hoe handles shallow weeding, soil loosening and trench work between rows without turning the bed over.

Tillers and Cultivators ·

Best Knee Pads for Landscaping (2026)

Five knee pads for landscaping work, from gel and hard shell designs to foam and sleeve styles, compared by cushion, straps, stated weight and…