Standard Grease Fitting Size Chart and Guide
A plain guide to the standard grease fitting size for mower and tractor zerks, with a size chart and four assortment kits to keep on hand.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
PAIGOIN 405-Piece SAE and Metric Grease Fitting Kit9.5/10View on Amazon - 2
OURU 260-Piece SAE and Metric Grease Fitting Kit9.5/10View on Amazon - 3
OURU 240-Piece SAE and Metric Grease Fitting Kit9.5/10View on Amazon - 4
NEIKO 50463A 110-Piece SAE Grease Fitting Kit9.4/10View on Amazon
A fitting with the wrong thread will not seat on a mower deck zerk, a tractor axle or a bearing housing, so the grease gun cannot do its job. The standard grease fitting size on most mowers and tractors is the SAE quarter-twenty-eight thread, with eighth-inch pipe thread and metric sizes also in wide use. This guide gives the size chart, shows how to match a fitting, and compares four assortment kits that cover the common sizes.
AcreMowerLab earns a commission when you shop through links here. It never changes your price. Affiliate disclosure.

PAIGOIN 405-Piece SAE and Metric Grease Fitting Kit
SAE and metric grease fitting assortment with 405 pieces, caps, sealing tape and a wrench kit in a reinforced storage box.
Who it's for: owners with several machines who want one kit for SAE and metric threads.
Who should skip it: owners with a single mower.
The PAIGOIN kit is the largest assortment here, with 405 pieces in 1/4-inch, 1/8-inch, M6, M8 and M10 sizes, in straight, 45-degree and 90-degree angles. The maker lists galvanized structural steel with plating for rust resistance, plus caps, sealing tape and a 7 to 11 mm wrench kit.
Pros
- Largest kit here, with 405 pieces
- Covers SAE and metric sizes to M10
- Caps, sealing tape and wrench kit included
- Reinforced storage box keeps fittings organized
Cons
- No weight is stated for the full box
- No case dimensions are stated
- 405 pieces is more than one mower needs
- Steel fittings still need the thread matched

OURU 260-Piece SAE and Metric Grease Fitting Kit
SAE and metric grease fitting assortment with 260 pieces, caps in two materials and a wrench set in a labelled storage case.
Who it's for: owners who want caps and a wrench with the fittings, in a case that fits a shelf.
Who should skip it: owners who want the largest piece count.
The OURU 260-piece kit covers 1/4-inch, 1/8-inch, M6, M8 and M10 sizes in straight, 45-degree and 90-degree angles, for lubrication points in tight spaces. The maker lists galvanized steel for corrosion resistance, a labelled case with thick partitions, caps in two materials and a 7 to 11 mm wrench set.
Pros
- Caps in two materials keep dust out
- Covers SAE and metric sizes to M10
- Wrench set in 7 to 11 mm sizes included
- Labelled case with thick partitions
Cons
- 260 pieces is fewer than the 405-piece kit
- No sealing tape is included
- Case suits a shelf, not a pocket
- Steel fittings still need the thread matched

OURU 240-Piece SAE and Metric Grease Fitting Kit
SAE and metric grease fitting assortment with 240 pieces and a wrench kit in five sizes in a labelled storage case.
Who it's for: owners who want a wrench kit with the fittings and a case that stays organized.
Who should skip it: owners who want caps in the box.
The OURU 240-piece kit covers 1/4-inch, 1/8-inch, M6, M8 and M10 sizes in straight, 45-degree and 90-degree angles, and the maker lists galvanized steel for corrosion, rust and oxidation resistance. The kit includes a wrench kit in five sizes and comes in a labelled case with thick partitions.
Pros
- Covers SAE and metric sizes to M10
- Wrench kit in five sizes included
- Galvanized steel resists corrosion outdoors
- Labelled case with thick partitions
Cons
- No caps are included for spare fittings
- No weight is stated for the full case
- 240 pieces is fewer than the larger kits
- No sealing tape is included

NEIKO 50463A 110-Piece SAE Grease Fitting Kit
SAE grease fitting assortment with 110 pieces in 1/4-28 and 1/8-inch pipe sizes, in A3 steel with a plastic storage case.
Who it's for: owners whose machines all use SAE threads and who want a light, cased kit.
Who should skip it: owners with metric zerks.
The NEIKO 50463A is the SAE-only kit here, with 110 pieces in A3 steel, including 30 straight 1/4-28 fittings, 20 straight 1/8-inch pipe fittings, and 15 each of the 45-degree and 90-degree 1/4-28 fittings. The maker lists the fittings as small hydraulic check valves that feed lubricant into a bearing without disassembly.
Pros
- 30 straight 1/4-28 fittings stated
- 20 straight 1/8-inch pipe fittings stated
- Angled 1/4-28 fittings in 45 and 90 degrees
- Smallest kit here at 1.0 lb, in a case
Cons
- SAE sizes only, so metric zerks need another kit
- 110 pieces is the smallest count here
- Angled fittings come in 1/4-28 only
- Plastic case is lighter duty than a reinforced box
Standard grease fitting size: the size chart
SAE sizes use inch threads, metric sizes use millimetre threads, and the angles are straight, 45-degree and 90-degree.
| Size | Thread | Angles |
|---|---|---|
| 1/4-28 | SAE | Straight, 45-degree, 90-degree |
| 1/8 in pipe | SAE pipe thread | Straight, 45-degree, 90-degree |
| M6, M8, M10 | Metric | Straight, 45-degree, 90-degree |
Check the 1/4-28 size first, then the 1/8-inch pipe size, then the metric sizes. A kit holding SAE and metric fittings covers a mixed shed. See the best grease gun picks for the tool that feeds these fittings.
How to match the fitting to the zerk on your machine
Start with the fitting already on the machine. Remove it and compare its thread and angle with the new fitting before fitting the replacement. The thread must match: a 1/4-28 fitting will not seat in a metric hole, and a metric fitting will not seat in a 1/4-28 hole. The angle matters where the zerk sits close to a frame rail, a guard or a wheel. Check the machine manual for the fitting size and the grease points it lists, and keep the old fitting until the new one is seated and greased.
Grease fitting assortment kits for mower and tractor zerks
Once the thread and angle are known, an assortment kit puts the common sizes in the shed, so the right fitting is on hand when a zerk needs attention.
Angles: straight, 45-degree and 90-degree fittings
Straight fittings suit open grease points where the coupler has a clear run at the zerk. A 45-degree fitting suits a zerk at an angle to the approach, and a 90-degree fitting suits a zerk tucked behind a guard or a frame member. Across the kits here, all three angles appear for the 1/4-28, 1/8-inch pipe and metric sizes.
SAE and metric sizes in one kit
Older mowers and tractors tend to use SAE threads, while newer machines and imported equipment may use metric threads. The NEIKO kit (on Amazon) here is SAE only. The OURU and PAIGOIN kits mix SAE and metric sizes, with 1/4-inch, 1/8-inch, M6, M8 and M10 fittings in all three angles.
Storage and keeping fittings organized
Small fittings are easy to lose, so the case matters as much as the count. The NEIKO kit comes in a plastic storage case with an organization chart and a compartment for each size. The OURU kits come in a labelled case with thick partitions. The PAIGOIN kit (on Amazon) comes in a reinforced storage box. Caps keep dust out of the fittings: the PAIGOIN kit includes caps and sealing tape, and the OURU 260-piece kit includes caps in two materials.
Safety
Wear eye protection when working under a mower or a tractor, and keep hands clear of blades, belts and hot parts. Support the machine as the manual directs before working underneath it, and keep children and pets out of the work area. Grease fittings with the machine parked and the engine off and cool.
FAQ: mowing large lots
What is the standard grease fitting size for a mower?
The standard grease fitting size on most mowers is the 1/4-28 SAE thread, in straight, 45-degree and 90-degree angles. Some machines use 1/8-inch pipe thread or metric sizes.
What is the difference between 1/4-28 and 1/8-inch pipe thread?
The 1/4-28 size is an SAE thread, while the 1/8-inch pipe size is a pipe thread. The two threads do not interchange, so match the thread already on the machine before fitting a replacement.
Are grease fittings SAE or metric?
Both. SAE sizes such as 1/4-28 are common on mowers and tractors, while metric sizes such as M6, M8 and M10 appear on newer machines and imported equipment.
What angle grease fitting fits a tight spot?
Use a straight fitting where the grease gun coupler has a clear run at the zerk. Use a 45-degree fitting where the approach is angled, and a 90-degree fitting where the zerk sits behind a guard or a frame member.
Do grease fitting kits include a wrench?
Some do. The OURU 240-piece kit includes a wrench kit in five sizes, and the other two kits include a 7 to 11 mm wrench set.




