Digging Bar vs Post Hole Digger: Which One Should You Buy?
A digging bar breaks rock and pries, a post hole digger makes the hole, and the right pick depends on how many holes the fence line needs.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Ashman Heavy-Duty Digging Shovel9.6/10View on Amazon - 2
Leriton 50" Chisel Digging Bar 12LbView on Amazon - 3
Leriton Tamping and Digging Bar Heavy Duty Steel Spud BarsView on Amazon - 4
Leriton 60"View on Amazon - 5
Leriton 48 Inch Tamping and Digging Bar Steel Bars Post HoleView on Amazon - 6
Leriton 69 Inch Tamping and Digging Bar Heavy Duty Steel SpudView on Amazon - 7
Leriton 48 Inch Tamping and Digging Bar Heavy Duty Steel SpudView on Amazon
A fence line starts with holes, and digging bar vs post hole digger is the choice between breaking ground and digging it. A digging bar is a long steel bar for breaking rock, cutting roots and prying, while a post hole digger cuts a round hole for the post. For fence posts, the digger makes the hole and the bar handles what the digger cannot cut. This guide compares each side and the digging tools in the gear section below.
Other machines to compare
Leriton 50" Chisel Digging Bar 12LbCheck price on Amazon
Leriton Tamping and Digging Bar Heavy Duty Steel Spud BarsCheck price on Amazon
Leriton 60"Check price on Amazon
Leriton 48 Inch Tamping and Digging Bar Steel Bars Post HoleCheck price on Amazon
Leriton 69 Inch Tamping and Digging Bar Heavy Duty Steel SpudCheck price on Amazon
Leriton 48 Inch Tamping and Digging Bar Heavy Duty Steel SpudCheck price on Amazon
AcreMowerLab earns a commission when you shop through links here. It never changes your price. Affiliate disclosure.
Digging bar vs post hole digger: which tool does the job
| Tool | Best for | Limit |
|---|---|---|
| Digging bar | Breaking rock, cutting roots, prying | Does not drill a round hole |
| Electric post hole digger | Drilling many post holes fast | Needs power and weighs 29.0 lb |
| Manual post hole digger | Digging a few holes with control | Slow for a long fence line |
The bar breaks what the digger cannot cut, and the digger cuts the hole the post sits in. A short run of posts can go in with the manual digger alone, while a long fence line goes faster with the electric auger. For a closer look at powered drilling, see the post hole digger vs auger comparison.
The gear
XtremepowerUS 1500W electric post hole digger
The electric auger leads this gear section: a 1500W motor, a 6-inch digging bit on a 3/4-inch shaft, and forward and reverse rotation. Reverse helps release the bit when it sticks in compacted soil or tangles with underground roots, and the spiral blade moves loosened soil upward as the auger turns. At 29.0 lb it suits a fence line with many holes, where the motor does the work a manual digger asks from arms and back. The maker gives 2 sizes for this auger, 17.0 by 33.0 by 13.0 inches and 23-1/4 by 15 by 43 inches, so check the size before ordering.
VEVOR manual post hole digger
The manual digger cuts 5.71-inch diameter holes with a metal blade on a 57.48-inch carbon steel handle. Scale markings on the handle help monitor digging depth in real time, and the hemp tail sleeve gives a strong anti-slip grip. At 11.46 lb it moves easily to distant work areas, and it needs no assembly and no power. The handle is Q235 carbon steel, 0.12-inch thick, paired with a 50Mn steel blade, and it suits loose soft soil and cultivable land.
Leriton chisel digging bar
The digging bar is a 50-inch hex shank of forged, heat-treated carbon steel, 25 mm in diameter with a 50 mm blade and a 60 mm conical sharpened length. One end is conical and the other is a sharpened flat end, so the same bar digs, pries dirt, cuts roots and breaks stubborn material. At 12 lb it is a single-piece tool with nothing to assemble, for builders and gardeners breaking up a road surface or cultivating a garden bed.
How to use them together
Start with the digger, and keep the bar within reach. Set the post hole digger over the mark and dig until the bit or blade meets rock or a root it cannot cut, then lift the digger out and work the spot with the bar. Use the conical end to break rock and the flat end to cut roots and pry, then dig again. Check depth with the VEVOR scale markings as the hole goes down, and use reverse on the electric auger when the bit sticks in compacted soil or tangles with roots.
Safety
Always check for underground utilities before digging and follow the manufacturer’s instructions. The manual digger needs no power and no fuel, so there is no cord or fuel to manage on that tool. Keep the work area clear and watch footing on rough ground, and stop when the tool hits something hard instead of forcing it.
FAQ: mowing large lots
Can a digging bar dig a fence post hole on its own?
A bar breaks rock, cuts roots and pries, but it does not drill a round hole. The VEVOR digger cuts 5.71-inch diameter holes and the electric auger takes a 6-inch bit, so use the digger for the hole and the bar for what the digger cannot cut.
How deep can a manual post hole digger go?
The VEVOR handle is 57.48 inches long with scale markings that help monitor digging depth in real time. Depth depends on the soil and the post, so check the markings as the hole goes down and stop at the depth the fence plan calls for.
What size hole does a post hole digger make?
The VEVOR manual digger cuts 5.71-inch diameter holes, and the electric auger comes with a 6-inch digging bit. Match the bit or blade to the post size before digging.
Do I need an electric post hole digger for a fence?
It depends on how many holes the fence needs. The 1500W electric auger with reverse suits a long fence line, while the 11.46 lb manual digger suits a short run of holes with no power to plug in.
What should I check before digging post holes?
Check for underground utilities before digging and follow the manufacturer’s instructions. Mark the post spots first so the holes land where the fence line runs.




