How to Adjust Mower Deck
Level the deck side to side with a blade gauge and adjust the lift linkage until both blade tips read the same.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
KH866 2-Pack Deck Leveling Gauge, 1-1/2 to 5 in9.6/10View on Amazon - 2
Oregon Universal Deck Leveling Gauge, 3-Month Warranty9.5/10View on Amazon - 3
HD Switch Deck Leveler Gage with Anti-Tip Base9.5/10View on Amazon - 4
DABAZUALY GX24864 Deck Lift Linkage Rod Kit9.5/10View on Amazon
An uneven cut often means the deck sits uneven. This guide shows how to adjust mower deck height so the blades cut level, using a blade gauge to measure and the lift linkage to set the height. Park on flat ground, measure the blade tips on each side, and turn the linkage until both sides match.
AcreMowerLab earns a commission when you shop through links here. It never changes your price. Affiliate disclosure.

KH866 2-Pack Deck Leveling Gauge, 1-1/2 to 5 in
Two-pack gauge that measures cutting heights from 1-1/2 to 5 inches.
Who it's for: owners who want to measure both blade tips with a gauge that covers 1-1/2 to 5 inches.
Who should skip it: anyone whose mower uses part numbers outside the listed set.
The KH866 is a two-pack deck leveling gauge that measures cutting heights from 1-1/2 to 5 inches. It fits John Deere AM130907 and TY15272, MTD 490-900-0041, Cub Cadet, Troy-Bilt and Stens 750-442, part number 16092025D.
Pros
- Measures cutting heights from 1-1/2 to 5 in
- Two gauges in the pack
- Fits John Deere, MTD, Cub Cadet and Troy-Bilt
- Lightweight and straightforward, per the maker
Cons
- Warranty term is not stated
- Measures only, it does not adjust the linkage
- Fits listed part numbers only, so match yours first
- Two gauges to keep track of

Oregon Universal Deck Leveling Gauge, 3-Month Warranty
Universal deck leveling gauge from Oregon, no assembly required, 3-month warranty.
Who it's for: owners who want a simple, no-assembly gauge for a quick blade check.
Who should skip it: anyone who wants a stated cutting height range.
The Oregon gauge is a universal small-engine deck leveling gauge that measures blade height to find an unlevel deck. The maker lists it as a genuine Oregon replacement part, part number 42-095, with no assembly required. It measures 2.0 by 2.0 by 2.0 inches, weighs 0.12 lb, and fits most standard riding and push lawn mowers.
Pros
- Genuine Oregon part, part number 42-095
- No assembly required
- Fits most standard riding and push mowers
- 3-month warranty stated on the listing
Cons
- Small 2.0 in size is easy to misplace
- One gauge in the pack
- No stated cutting height range
- Fixes blade level only, not worn linkage

HD Switch Deck Leveler Gage with Anti-Tip Base
Deck leveler gage with a rigid arm and anti-tip base for John Deere and MTD mowers.
Who it's for: owners who want a rigid, stable gage that stays standing while they adjust the deck.
Who should skip it: anyone who wants a stated warranty.
The HD Switch gage has a measurement arm the maker states is 100% thicker than competitive gauges, which prevents flexing and supports accurate, repeatable measurements. The base is completely flat, and a stabilizer extension adds stability and keeps the gage from falling over. It fits John Deere AM130907, MTD 490-900-0041, Stens 750-442, Cub Cadet, Troy-Bilt, Scotts and Sabre mowers.
Pros
- Arm is 100% thicker than competitive gauges, per the maker
- Anti-tip base keeps the gage standing during adjustments
- Flat base for accurate, repeatable measurements
- Fits John Deere, MTD, Cub Cadet and Troy-Bilt
Cons
- Warranty term is not stated
- Extended base takes more room in storage
- Fits listed part numbers only, so match yours first
- Measures only, it does not adjust the linkage

DABAZUALY GX24864 Deck Lift Linkage Rod Kit
Two sets of GX24864 deck lift linkage rods for John Deere 100 Series tractors.
Who it's for: owners of a listed John Deere 100 Series tractor whose deck will not stay level.
Who should skip it: anyone who only needs to measure blade height.
The DABAZUALY kit is two sets of GX24864 mower deck lift linkage rods for John Deere 100 Series tractors, covering the D, L, X, S and E lines of the John Deere 100 Series. Each set includes GX24864 rods with GX21718, 24M7053 and GX26085 hardware. The rods measure 4.0 by 0.8 by 0.8 inches.
Pros
- Two sets included in the pack
- Fits John Deere 100 Series tractors, per the listing
- Includes GX21718, 24M7053 and GX26085 hardware
- Lift linkage rods that set deck height
Cons
- John Deere 100 Series only, so check your model first
- Linkage rods only, no gauge for measuring blade height
- Fitting means removing the old linkage rods first
- Two sets means spares to store if one side is worn
How to adjust mower deck: read the cut first
Walk the lawn after a mow and look at the cut before touching the deck. A deck that sits low on one side leaves that side shorter, while a deck that is unlevel front to back leaves an uneven finish. Note which side cuts low, then measure rather than guessing. A gauge gives a repeatable reading from the blade tip for every change that follows.
Park on flat ground
Roll the mower onto flat, hard ground and set the parking brake. Lower the deck to a mowing height and shut the engine off. Let the engine cool before reaching under the deck, and keep children and pets out of the work area. Clear sticks and stones from under the deck so the gauge sits flat. A slope tilts every reading, so move the mower if the ground falls away on one side.
Measure both blade tips
Turn one blade so its tip points to the side of the deck and set the gauge under the tip. Read the height, then read the other side the same way, and do the same for the other blade. Write the readings down side by side so you can see which side sits low. The KH866 gauge (on Amazon) measures cutting heights from 1-1/2 to 5 inches. If the two sides read the same, the deck is level side to side.
Adjust the lift linkage
Find the lift linkage rods that connect the deck to the lift arms. Turn the adjusters a little at a time, then measure again after each change, until both blade tips read the same. Work on the low side first and recheck the high side after every change, since raising one side can move the other. If the rods are bent or the threads are worn, adjustment may not hold, and fresh rods such as the DABAZUALY GX24864 kit (on Amazon) give the deck a sound starting point. See our lawn mower deck repair guide for the parts the job needs.
Recheck the cut
Mow a short strip on flat ground and look at the finish before mowing the whole lawn. A level deck leaves an even cut across its width. If one side still cuts low, measure again and adjust once more. Check the deck again after the first full mow, and clean the deck underside when the job is done. See our how to clean a mower deck guide for the underside routine.
Deck leveling gear for this job
Measuring blade height calls for a gauge, and holding the setting calls for sound lift linkage, so these 4 tools cover both parts of the job.
Safety
Work on flat ground with the engine off and cool, and keep the key out of the ignition while your hands are under the deck. Wear eye protection and sturdy shoes, and keep children, pets and bystanders away. Never reach under a deck while the blades can still turn, and never start the engine with anyone near the deck.
FAQ: mowing large lots
How do I know if my mower deck is unlevel?
Mow a strip and look at the finish. One side cutting shorter than the other, or a stepped line between passes, points to a deck that sits uneven. Measure both blade tips with a gauge before turning any linkage.
What tool measures mower blade height?
A deck leveling gauge sits under the blade tip and reads its height from the ground. The KH866 gauge measures cutting heights from 1-1/2 to 5 inches.
Do I measure the deck or the blades?
Measure the blade tips. The blades do the cutting, so their height on each side is the reading that matters. Set the gauge under the tip on each side and compare the readings before adjusting anything.
Can worn lift linkage keep a deck from staying level?
Yes. Bent rods or worn threads let the setting drift after adjustment. The DABAZUALY GX24864 kit replaces the lift linkage rods on listed John Deere 100 Series tractors.
Should the front of the deck sit lower than the rear?
Follow your mower manual for the front-to-rear setting. Measure the blade tips at the front and the rear with the gauge, set them to the manual setting, then recheck after the first mow.




