How to Set Spark Plug Gap on a Small Engine
A feeler gauge and a gapping tool set the gap on a small engine spark plug: measure the gap, adjust the side electrode, and check it again before the plug goes back in.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
OEMTOOLS 25442 9-Wire Spark Plug Gap Gauge9.5/10View on Amazon - 2
GZZTORES Spark Plug Gap Tool with 32 Blade Feeler Gauge9.5/10View on Amazon - 3
PQY Spark Plug Gap Tool with 32 Blade Feeler Gauge9.5/10View on Amazon - 4
OLLBIT Spark Plug Gapper Coin Gauge .020 to .1009.4/10View on Amazon
A mower that cranks, sputters and dies on a cold morning can have a plug gap that drifted over the season. How to set spark plug gap on a small engine comes down to a feeler gauge, a gapping tool and the gap the engine or plug maker lists for the plug. Pull the plug, measure the gap, move the side electrode until the feeler drags, and check the gap again before the plug goes back in.
AcreMowerLab earns a commission when you shop through links here. It never changes your price. Affiliate disclosure.

OEMTOOLS 25442 9-Wire Spark Plug Gap Gauge
A 9-wire gap gauge with wires from .025 to .060 inch, inch and millimeter scales, and a limited lifetime warranty.
The OEMTOOLS 25442 is a 9-wire gauge with wires from .025 to .060 inch, and it carries inch and millimeter scales, which the listing states suit various vehicle makes and models. The gauge is compact at 5.2 by 3.1 by 0.4 inches, and the listing states it fits in a tool chest or pocket. The warranty is a limited lifetime term, the strongest warranty term here.
The gauge measures only, so you still need a way to move the electrode once you read the gap. Its range covers .025 to .060 inch, which leaves gaps outside that range to a different gauge. The markings are clear and distinct, per the listing, for quick readings.
Pros
- 9 wire sizes from .025 to .060 inch for precise measurement
- Inch and millimeter scales on the gauge
- Limited lifetime warranty stated on the listing
- Compact gauge that fits in a tool chest or pocket
Cons
- Measures only, with no gapping tool to move the electrode
- Range ends at .060 inch, so wider gaps need a different gauge
- No wires below .025 inch in the set
- No storage case is stated in the listing

GZZTORES Spark Plug Gap Tool with 32 Blade Feeler Gauge
An aluminum gapping tool with a 32-blade steel feeler gauge, range 0.0015 to 0.035 inch, for 10, 12, 14 and 16 mm plugs, with a 1 year warranty.
The GZZTORES tool pairs an aluminum gapping tool with a 32-blade steel feeler gauge, range 0.0015 to 0.035 inch (0.04 to 0.88 mm). Place the plug on the tool, pick a feeler, and screw the knob until the side electrode compresses to the gap. It fits most 10, 12, 14 and 16 mm standard spark plugs, and the listing states a 1 year warranty.
The listing warns that some electrodes spring back, and suggests a 0.36 mm feeler for a 0.38 mm target so the gap lands on target after the spring-back. The feeler blades are manganese steel, and the tool is aluminum. The listing does not state a brass blade, a weight, or dimensions.
Pros
- 32-blade feeler gauge, range 0.0015 to 0.035 inch (0.04 to 0.88 mm)
- Aluminum gapping tool with a screw knob to move the electrode
- Fits most 10, 12, 14 and 16 mm standard spark plugs
- 1 year warranty stated on the listing
Cons
- No brass blade for electronic ignitions is stated
- Long reach and short reach fit are not stated
- Weight and dimensions are not stated
- Fit for 18 mm plugs is not stated

PQY Spark Plug Gap Tool with 32 Blade Feeler Gauge
An aluminum gapping tool with a 32-blade feeler gauge, range 0.0015 to 0.035 inch, with a 0.010 inch brass blade for electronic ignitions.
The PQY tool is an aluminum gapping tool with a 32-blade feeler gauge, range 0.0015 inch (0.04 mm) to 0.035 inch (0.88 mm). The title calls the blades stainless steel, but the bullets call them manganese steel, so the listing contradicts itself on the blade material. Place the plug on the gapper, pick a feeler, and screw the knob slowly until you reach the gap. It includes a 0.010 inch (0.25 mm) brass blade for electronic ignitions, the only brass blade here.
The tool fits most 10, 12, 14 and 16 mm standard spark plugs, but not 18 mm thread, and not long reach or short reach plugs, so check the plug size before purchase. The listing warns that some electrodes spring back, and suggests a 0.42 mm feeler for a 0.44 mm target. The listing states no warranty term.
Pros
- 32-blade feeler gauge, range 0.0015 inch (0.04 mm) to 0.035 inch (0.88 mm)
- Includes a 0.010 inch (0.25 mm) brass blade for electronic ignitions
- Aluminum gapping tool with a screw knob to move the electrode
- Fits most 10, 12, 14 and 16 mm standard spark plugs
Cons
- Does not fit 18 mm thread plugs
- Does not work for long reach or short reach plugs
- No warranty term is stated
- Weight and dimensions are not stated

OLLBIT Spark Plug Gapper Coin Gauge .020 to .100
A zinc alloy coin gauge scaled from .020 to .100 inch, 1.5 inches across and 17 grams, with inch graduations on the front and millimeter graduations on the back.
The OLLBIT gauge is a zinc alloy coin tool scaled from .020 to .100 inch, with inch graduations on the front and millimeter graduations on the back. It is 1.5 inches across and weighs 17 grams, with a hanging hole for a keyring or backpack. The grooves along the edges help with gap adjustments, and the edges are polished to remove sharp corners.
The range tops out at .100 inch, the highest top end here, but it starts at .020 inch, so finer gaps need a feeler gauge. The listing states the tool is robust and wear-resistant, with weather resistance and corrosion resistance. No warranty term and no plug thread fit list are stated.
Pros
- Scaled from .020 to .100 inch, the widest top end here
- Inch graduations on the front and millimeter graduations on the back
- 1.5 inches across and 17 grams, with a hanging hole for a keyring
- Polished edges with no sharp corners, to prevent hand injuries
Cons
- No feeler blades and no screw knob in the set
- No warranty term is stated
- No fit list for plug thread sizes is stated
- No measurement below .020 inch in the range
Other machines to compare
ELEAD 6-Piece 3/8" Drive Spark Plug Socket Set with SparkCheck price on Amazon
ELEAD 8-Piece 3/8" Drive Spark Plug Socket Set with UniversalCheck price on Amazon
12-Piece 3/8" Drive Spark Plug Socket Set with Ratchet HandleCheck price on Amazon
5PCS Magnetic Spark Plug Socket Set Includes 14mm 16mm ThinCheck price on Amazon
TecoTek 11-Piece Spark Plug Socket Set with 3/8" DriveCheck price on Amazon
LLNDEI 3/8-Inch Drive Magnetic Swivel Spark Plug Socket SetCheck price on Amazon
How to set spark plug gap: the tools that do it
| Tool | Best for | Limit |
|---|---|---|
| 32-blade feeler gauge | Measuring gaps from 0.0015 to 0.035 inch | Measures only, does not move the electrode |
| Gapping tool with knob | Holding the plug while you set the gap | Fits 10 to 16 mm plugs; check the size before purchase |
| 9-wire gauge | Measuring gaps from .025 to .060 inch | Range ends at .060 inch |
| Coin gauge | Measuring gaps from .020 to .100 inch | Measures only; no feeler blades |
A feeler gauge with a gapping tool covers the job, and a wire gauge works for a quick check. See the best spark plug gap tool for small engines roundup for more gap tools, and the mower maintenance hub for more upkeep gear.
Pull the plug and measure the gap
Let the engine cool, then pull the spark plug wire off the plug and remove the plug with a socket. Wipe the plug clean and look at the electrodes for wear. Slide the feeler blade or wire that matches the listed gap into the gap: if it slides through with no drag, the gap is wide; if it will not fit, the gap is tight. Note the reading before you adjust anything.
Adjust the side electrode
Set the plug in the gapping tool and pick the feeler that matches the gap the engine or plug maker lists. Screw the knob slowly until the side electrode presses the feeler, then back the knob off and pull the feeler out. Some electrodes spring back, so the PQY listing suggests a 0.42 mm feeler for a 0.44 mm target, and the GZZTORES listing suggests a 0.36 mm feeler for a 0.38 mm target. Measure again after each adjustment, and stop when the feeler drags slightly at the listed gap.
Check the gap again before the plug goes back in
Slide the feeler through the gap again: it should drag slightly, not slide freely and not stick. If the gap moved while you handled the plug, set it again with the tool. Put the plug back in, tighten it with a socket, and push the spark plug wire back on until it seats. Start the engine and listen for a steady idle before you mow.
The tools: feeler gauges and gapping tools
The gap is measured in thousandths of an inch or in millimeters, so the tool you pick decides how fine a feeler you can read and whether you can move the electrode with a knob.
Safety
Let the engine cool before you pull the plug, and keep the spark plug wire off while you work. Wear eye protection and keep children and pets out of the work area. Refuel only with the engine off and cool. If the plug is seized or the threads look damaged, ask a repair shop instead of forcing it.
FAQ: mowing large lots
What gap should a small engine spark plug have?
The gap comes from the engine or plug maker, not from the tool: check the manual or the plug maker’s listing for the figure. The feeler gauges here measure from 0.0015 to 0.035 inch, the wire gauge from .025 to .060 inch, and the coin gauge from .020 to .100 inch. Set the gap to the listed figure and check it again before the plug goes back in.
Can I gap spark plugs without a tool?
A feeler gauge is the tool for the job, and the gauges here all measure the gap with blades, wires or a coin gauge. Without a gauge you cannot read the gap, so pick a gauge that covers the gap the maker lists. The OLLBIT coin gauge is 1.5 inches across and weighs 17 grams, so it rides in a pocket.
Why does my spark plug gap keep changing?
Some electrodes spring back after you set them, so the PQY listing suggests a 0.42 mm feeler for a 0.44 mm target and the GZZTORES listing suggests a 0.36 mm feeler for a 0.38 mm target. Measure again after each adjustment, and stop when the feeler drags slightly at the listed gap.
Do I need a different tool for 10 mm and 16 mm plugs?
The PQY and GZZTORES tools (on Amazon) fit most 10, 12, 14 and 16 mm standard spark plugs. The PQY tool does not fit 18 mm thread plugs, and does not work for long reach or short reach plugs. Check the plug size before you order, as the listings advise.
How do I know if my spark plug is worn out?
Look at the electrodes for wear and check the gap: a gap that has grown wider than the listed figure after a season of use points to a worn plug. The listings here do not state wear limits, so compare the plug with a new plug of the same type. If the plug is worn, see the types of spark plugs guide before you pick a replacement.




