John Deere X330 vs Cub Cadet XT1: Which One Should You Buy?
The John Deere X330 and the Cub Cadet XT1 compared through the deck belts each tractor takes: length, cord, fit and warranty, with one belt example for each side.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Tecreddy 954-05021 42 Inch Deck Belt for Cub Cadet XT19.6/10View on Amazon - 2
UDC Parts M174994 42 Inch Deck Belt for John Deere X3309.4/10View on Amazon
Verdict: Choose the John Deere X330 side if you mow with an X330, X350, X354 or X370 with a 42 inch deck. Choose the Cub Cadet XT1 side if you mow with an XT1 LT42 with a 42 inch deck: the Tecreddy belt is the one of the two that states a 1 Year warranty.
A lawn tractor earns its keep on the ground around the house, the beds, the trees and the strip along the drive. The john deere x330 vs cub cadet xt1 question comes down to the belt each tractor takes, since the deck belt carries drive to the blades under the deck. When the belt wears, the cut goes ragged and the blades slow. This comparison covers the two belts the listings offer, one for each tractor, and what they state about length, cord, fit and warranty.
AcreMowerLab earns a commission when you shop through links here. It never changes your price. Affiliate disclosure.
The two examples

Tecreddy 954-05021 42 Inch Deck Belt for Cub Cadet XT1
A replacement deck belt for the Cub Cadet XT1 LT42 with a 42 inch deck, part 954-05021, with aramid cord, Kevlar fiber cores and neoprene rubber, in a 1/2 in width with a stated length of 99.75 in in the title and 100 in in the bullets, and a 1 Year warranty.
Who it's for: an owner of an XT1 or XT2 LT42 or LX42 with a 42 inch deck who needs the 954-05021 belt.
Who should skip it: anyone whose tractor takes a different belt length or part number, and anyone mowing with a John Deere X330, which takes the longer M174994 belt.
The Tecreddy belt is a replacement deck belt for the Cub Cadet XT1 LT42 with a 42 inch deck, listed as part 954-05021. The title states a 99.75 in length while the bullets state 100 in, so the length is listed two ways; the width is 1/2 in in both. The listing states aramid cord, neoprene rubber, polyester fiber and Kevlar fiber cores, and a 1 Year warranty. It also fits the XT2 LT42 and LX42, plus Craftsman, Troy-Bilt, MTD and Columbia models with a 42 inch deck, and describes the swap as DIY-friendly, with no special tools needed.
Pros
- Fits the XT1 LT42 with a 42 inch deck, plus XT2 and LX42 models
- Aramid cord with Kevlar fiber cores and neoprene rubber
- 1 Year warranty stated
- Listing claims 30% less wear than standard belts
Cons
- Length is listed two ways: 99.75 in in the title, 100 in in the bullets
- A belt only: no engine, transmission or slope figure for the XT1 itself
- Weight is stated as 0.61 pounds, an oddly precise figure
- The 1 Year warranty states a term but no coverage detail

UDC Parts M174994 42 Inch Deck Belt for John Deere X330
A replacement deck belt for the John Deere X330 with a 42 inch deck, part M174994, with aramid tensile cords, a natural rubber body and a two-layer wrapping cover, in a 1/2 in by 144.8 in size.
Who it's for: an owner of an X330, X350, X354 or X370 with a 42 inch deck who needs the M174994 belt.
Who should skip it: anyone whose tractor takes a different belt length or part number, and anyone who wants a stated warranty term, since this listing states none.
The UDC belt is a replacement deck belt for the John Deere X330 with a 42 inch deck, listed as part M174994. The listing states a 1/2 in width and a 144.8 in length, aramid tensile cords, a natural rubber body and a two-layer wrapping cover, with a tolerance of ±0.40 in. It also fits the X350, X354 and X370 with a 42 inch deck. This listing is a replacement belt, not a tractor, so it states no engine, transmission or slope figure for the X330.
Pros
- Fits the X330 with a 42 inch deck, plus the X350, X354 and X370
- Aramid tensile cords with a natural rubber body
- Two-layer wrapping cover over the rubber body
- Length and width stated plainly: 144.8 in by 1/2 in
Cons
- Warranty is not stated on the listing
- Weight is not stated
- A belt only: no engine, transmission or slope figure for the X330 itself
- Fits only the 42 inch deck models named, so check the deck before ordering
John Deere X330 vs Cub Cadet XT1 side by side
| Factor | John Deere X330 (UDC M174994 belt) | Cub Cadet XT1 (Tecreddy 954-05021 belt) | |
|---|---|---|---|
| Deck size (stated) | 42 in | 42 in | |
| Belt length (stated) | 144.8 in | 99.75 in in the title, 100 in in the bullets | |
| Belt width (stated) | 1/2 in | 1/2 in | |
| Cord | Aramid tensile cords | Aramid cord, Kevlar fiber cores | |
| Belt body | Natural rubber, two-layer wrapping cover | Neoprene rubber, polyester fiber | |
| Fits | X330, X350, X354, X370 with a 42 in deck | XT1 and XT2 LT42, LX42 with a 42 in deck | |
| Warranty (stated) | Not stated | 1 Year | |
| Item weight (stated) | Not stated | 0.61 pounds |
Figures are manufacturer stated for the two example models, collected 9 November 2026.
Deck belts: what the listings actually cover
Neither listing in this comparison is a tractor. Each one is a replacement deck belt for a 42 inch deck: the UDC belt for the John Deere X330 side, and the Tecreddy belt for the Cub Cadet XT1 side. That shapes everything that follows. Neither listing states an engine figure, a transmission type or a slope figure, so this comparison cannot say which tractor climbs, hauls or cuts better. It can say which belt fits which tractor, how the two belts differ in length and build, and which one states a warranty.
Belt length and deck fit
Both belts fit a 42 inch deck, and both are 1/2 in wide. The lengths differ: the UDC belt states 144.8 in, while the Tecreddy belt states 99.75 in in its title and 100 in in its bullets. A belt that fits one deck does not fit the other, so match the part number before ordering: M174994 for the X330 side, 954-05021 for the XT1 side. The UDC belt also fits the X350, X354 and X370 with a 42 inch deck. The Tecreddy belt also fits the XT2 LT42 and LX42 with a 42 inch deck, plus the Craftsman, Troy-Bilt, MTD and Columbia models the listing names.
Cord, rubber and build
Both belts use aramid cord. The UDC belt pairs aramid tensile cords with a natural rubber body and a two-layer wrapping cover, and states a tolerance of ±0.40 in. The Tecreddy belt pairs aramid cord with neoprene rubber and polyester fiber, and adds Kevlar fiber cores. The Tecreddy listing claims 30% less wear than standard belts and describes the swap as DIY-friendly, with no special tools needed.
Warranty and upkeep
The Tecreddy belt is the only one of the two that states a warranty: 1 Year. The UDC listing states no warranty term, so its warranty score is zero. A deck belt is a wear part, so look it over when the cut goes ragged, and keep the deck clear of packed grass and debris. Refuel with the engine off and cool, and keep children and pets out of the yard while mowing.
Acreage and terrain fit
Tecreddy 954-05021
UDC M174994
Matching It to Your Property
- Both examples fit 42 inch decks, so the deck width is the same on either side; the choice turns on which tractor the belt fits.
- The UDC belt fits the X330, X350, X354 and X370 with a 42 inch deck, so it suits an owner who already mows with one of those tractors.
- The Tecreddy belt fits the XT1 and XT2 LT42 and LX42 with a 42 inch deck, plus the Craftsman, Troy-Bilt, MTD and Columbia models the listing names, so it suits an owner with one of those tractors.
- Neither listing states a slope figure, an engine figure or a transmission type, so neither belt settles which tractor suits steep ground or heavy hauling.
The Acre Score explained
The Acre Score weighs five factors: performance, build quality, value, safety and warranty. A factor the listing does not state scores zero, which is why both examples score zero for safety, and the UDC example scores zero for warranty. The Tecreddy example leads because its listing states more: a 1 Year warranty, an item weight, and a wider fit list, on top of the aramid cord and Kevlar fiber cores.
| Product | Acre Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| Tecreddy 954-05021 | 9.6 | 28 | 20 | 19 | n/a | 3 |
| UDC M174994 | 9.4 | 26 | 19 | 18 | n/a | 0 |
We show weighted point totals as scores from a 9.2 base up to a 9.8 peak, and a larger total can never read lower. Safety is scored for gas, battery and electric equipment and for listings stating safety features; for anything else the score is taken over 90 points.
If you are still choosing the tractor itself, see the riding mower for 1 acre picks for decks and sizes.
Never mow a slope steeper than the maximum your manual lists, and mow up and down slopes rather than across. Use the ROPS and seat belt where the machine has them (follow the manual on when a folding ROPS may be lowered), never carry passengers, keep children and pets out of the yard while you mow, and disengage the blades before reversing. Refuel only with the engine off and cool. See CPSC riding lawnmower safety. Read our Safety Disclaimer.
FAQ: mowing large lots
Can I use the X330 belt on a Cub Cadet XT1?
No. The UDC belt for the X330 states a length of 144.8 in, while the Tecreddy belt for the XT1 states 99.75 in in its title and 100 in in its bullets. The two lengths differ, so each belt fits the deck it was made for: M174994 on the X330 side, 954-05021 on the XT1 side.
Do both belts fit a 42 inch deck?
Yes. Both listings state a 42 inch deck: the UDC belt for the X330, X350, X354 and X370, and the Tecreddy belt for the XT1 and XT2 LT42 and LX42. Check the deck size on the tractor before ordering, since each belt fits only the deck models its listing names.
Which belt states a warranty?
The Tecreddy belt for the XT1 states a 1 Year warranty. The UDC belt for the X330 states no warranty term, so its warranty score is zero. A stated term is a plus, but it covers the belt, not the tractor.
What are the belts made of?
Both use aramid cord. The UDC belt pairs aramid tensile cords with a natural rubber body and a two-layer wrapping cover. The Tecreddy belt pairs aramid cord with neoprene rubber and polyester fiber, and adds Kevlar fiber cores.
How do I know which belt my tractor takes?
Match the part number the listing states to the tractor and deck. The X330 with a 42 inch deck takes M174994. The XT1 LT42 with a 42 inch deck takes 954-05021. If the part number does not match, the belt does not fit, whatever the deck size.




