Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Pressure Washer Quick Connect Sizes Explained

The thread size and the snap fitting size decide whether a pressure washer gun, hose and pump connect, and this guide shows how to match them.

Pressure Washer Quick Connect Sizes Explained
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Pniimoo M22 to 3/8 Pressure Washer Quick Connect KitPniimoo M22 to 3/8 Pressure Washer Quick Connect Kit9.7/10View on Amazon
  2. 2Hotop 3/8 NPT Stainless Steel Pressure Washer Quick ConnectHotop 3/8 NPT Stainless Steel Pressure Washer Quick Connect9.7/10View on Amazon
  3. 3EARLEAS M22 Quick Connect Kit 9-Piece 5000 PSIEARLEAS M22 Quick Connect Kit 9-Piece 5000 PSI9.7/10View on Amazon

A driveway, a deck and a stretch of siding all need washing before the season turns, and the fittings on the washer decide whether the gun, hose and pump connect or sit apart as mismatched parts. Pressure washer quick connect sizes are the thread size on the pump and gun and the snap fitting size on the hose, and each size must match at its joint for the washer to run.

AcreMowerLab earns a commission when you shop through links here. It never changes your price. Affiliate disclosure.

Pressure washer quick connect sizes: the thread and the snap fitting

The sizes in this guide are the M22 thread and the 3/8-inch snap fitting. The M22 14mm thread is the threaded end that screws onto the pump, the gun or the hose end, and the 3/8-inch quick connect is the snap fitting that pushes together and pulls apart. A set such as the Twinkle Star set holds 4 pieces in 2 sets: an M22-14 swivel plus a 3/8-inch plug, and a 3/8-inch QD plus an M22-14 male end. The swivel end turns while the thread stays tight, and the plug snaps into the QD end.

Joint Fitting How it connects
Pump outlet M22 14mm thread Screws on, swivel end turns
Gun inlet M22 14mm thread Screws on, swivel end turns
Hose end 3/8-inch quick connect Snaps together, pulls apart to release

See the pressure washer hose size guide for hose length and fitting choices, and the pressure washer gun parts guide for gun fittings.

Read the thread size first

Start at the pump and the gun, and read the thread size on each fitting. The Twinkle Star set uses an M22 14mm thread, and the thread must match the thread on the pump and the gun. A thread that looks close but is not the same size will not seal, and the joint can leak at the washer. The Twinkle Star set is made of brass, and the maker lists a max pressure of 5000 PSI and a max working temperature of 300 degrees Fahrenheit for the set. For material choices, see the brass vs stainless pressure washer quick connect comparison.

Check the snap fitting size

The snap fitting joins the hose to the gun and the pump with a push, and no thread turns to make the joint. The Twinkle Star set uses a 3/8-inch quick connect, listed as 9.5mm in the set size, and the plug and the QD end must be the same size to snap together. The maker describes the 3/8-inch quick connect fittings as smooth to attach and release, and the set is simple to assemble and disassemble when the hose comes off for storage.

Watch for the M22 15mm fitting

Not every M22 thread is the same size. The Twinkle Star set does not fit electric pressure washers of Sun Joe, Campbell, MI-T-M, AR Blue, Stanley, Cleanforce and Simoniz with an M22 15mm fitting. Read the fitting size on the washer before ordering, and match the thread on the pump, the gun and the hose end to the same size. A fitting that does not match can thread on yet still leak, so check the size on the washer first and order the set that matches it.

Put the set together in order

Work from the pump to the gun so each joint is checked as it is made. Screw the M22-14 swivel onto the pump outlet, snap the 3/8-inch plug into the QD end, and screw the M22-14 male end onto the gun. The set covers gun, hose and pump connections, so the same sizes serve each joint on a washer that matches them. Check each joint for a snug fit before the washer runs, and keep the fittings clean so the snap ends seat fully.

Safety

Wear eye and hearing protection and sturdy shoes, and keep children, pets and bystanders away from the work area. Never point the spray at people or animals, and run a gas washer outdoors only. Clear the area of loose debris before washing, and follow the washer manual for pressure and nozzle choices. The pressure washer nozzle types guide explains the tip sizes.

FAQ: mowing large lots

What size is a pressure washer quick connect?

The size has a thread part and a snap part. The Twinkle Star set uses an M22 14mm thread and a 3/8-inch quick connect, listed as 9.5mm in the set size, and each part must match the fitting on the pump, the gun and the hose.

What does M22 14mm mean on a pressure washer fitting?

M22 14mm is the thread size on the fitting. The M22 thread screws onto the pump, the gun or the hose end, and a fitting with a different thread size will not seal on that joint.

Will an M22 14mm fitting work on a Sun Joe pressure washer?

Not on the electric pressure washers named in the Twinkle Star set description. The set does not fit electric pressure washers of Sun Joe, Campbell, MI-T-M, AR Blue, Stanley, Cleanforce and Simoniz with an M22 15mm fitting, so check the fitting size on the washer before ordering.

How much pressure can a brass quick connect fitting handle?

The maker rates the Twinkle Star brass set at a max pressure of 5000 PSI. Match the fitting rating to the washer, and do not run the washer past the rating on the fitting.

How hot can the water be through a quick connect fitting?

The maker lists a max working temperature of 300 degrees Fahrenheit for the Twinkle Star set. Keep the water within that rating, and let the fittings cool before handling them after a hot wash.

More mowing guides

More buying guides