Pressure Washer Hose Sizes: Length and Fitting Guide
Length, inner diameter, fittings and pressure ratings: how to pick a pressure washer hose that matches the washer and the job.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Flexzilla Pressure Washer Replacement Hose 1/4 in. x 50 ft.9.7/10View on Amazon - 2
Hourleey 100FT Pressure Washer Hose9.7/10View on Amazon - 3
Blu Shield The Slayer 3/8 in x 50 ft Pressure Washer Hose9.7/10View on Amazon
A driveway filmed with grit after winter, a patio green with algae, a fence that needs a wash before paint: each job starts the same way, with the washer parked in a spot and the work spread out around it. The hose is what connects the two, and pressure washer hose size decides how far the spray reaches, how much water moves through it, and which fittings thread onto the washer and the gun. This guide explains length, inner diameter, fittings and pressure ratings in order, so the hose matches the washer and the job.
AcreMowerLab earns a commission when you shop through links here. It never changes your price. Affiliate disclosure.
Pressure washer hose size: length, diameter and fittings
A hose size has parts: length, inner diameter and fittings. Length sets reach. Inner diameter sets how much water can pass through at a given pressure. Fittings set whether the hose threads onto the washer and the gun at all. The table below gives the stated figures for the hose in this guide, and the sections after it explain each part in turn.
| Part | What to check | Stated figure |
|---|---|---|
| Length | How far the spray must reach from the washer | 100 ft |
| Inner diameter | How much water the hose carries | 1/4 inch |
| Quick connect | How the hose joins the washer and gun | 3/8 inch |
| Fitting | The thread adapter in the box | M22 14 mm |
| Working pressure | The pressure the hose is rated for | 4200 PSI |
| Burst pressure | The pressure at which the hose fails | 16000 PSI |
| Flow rate | The water the hose is rated to carry | 2.5 to 5 GPM |
| Max temperature | The warmest water the hose takes | 140 F (60 C) |
For washers around the house, the best pressure washer for home use roundup lists washers by PSI and flow, which are the same figures to match on the hose.
Step 2: pick the length
Start from where the washer will sit and walk to the far end of the work. The hose must reach that point with slack left over, so it never pulls tight at the gun or drags the washer along. A hose that is too short turns a wash into a shuffle of the washer, while a hose that is far longer than the job needs is heavy to drag and slow to roll up. The hose in this guide is 100 ft long, which suits a driveway, a patio and a fence line from a single parking spot. Lay the hose flat to its full length the first time you use it, as the maker suggests, so it uncoils without kinks.
Step 3: match the diameter to the flow
Inner diameter is the bore of the hose, and it sets how much water can pass through at a given pressure. The hose in this guide has a 1/4 inch inner diameter, and the maker lists a flow rate of 2.5 to 5 GPM for it. The maker also notes that the 1/4 inch bore keeps the hose lighter in weight and smaller in volume than a wider bore, which makes it easier to carry, drag and roll up. Match the hose’s flow rating to the flow the washer is rated for, and check the washer manual for the flow it needs before ordering a hose.
Step 4: match the fittings
Fittings are where most hose buys go wrong, because a hose that does not thread on is useless no matter how good the rest of it is. The hose in this guide has a 3/8 inch quick connect, which joins and releases by hand and holds firm once seated. The box holds two adapters: an M22 14 mm female to 3/8 inch male plug and an M22 14 mm female to 3/8 inch female coupler. Check the threads on the washer outlet and on the gun before ordering, and match them to the quick connect and the adapters in the box.
Step 5: check the pressure rating
Every hose has a working pressure, and the working pressure is the figure to match. The maker rates this hose at 4200 PSI working pressure, with a burst pressure of 16000 PSI. The hose is built with a steel wire braid and a synthetic rubber inner tube. Match the working pressure to the washer, and never run a washer whose rating sits above the hose rating. For more on washer ratings, see the pressure washer reviews.
Keep the hose from kinking
A kink cuts flow and wears the braid, so the way the hose is handled matters as much as its size. The maker lists kink resistance as a feature of this hose, and suggests laying it flat to its full length the first time you use it. Roll it up in wide loops after the work, and keep it off sharp edges and out from under tires and mower wheels. A reel cart keeps the loops even and the hose off the ground; see the best hose reel cart picks. If a hose is cut or starts to leak at a fitting, the high pressure hose repair kit guide covers what to buy.
Mind the water temperature
Most washing runs on cold water from the tap, but some jobs call for warm water, and a hose has a limit. The maker lists a max working temperature of 140 F (60 C) for this hose. Stay inside that limit, and check the washer manual for its own temperature limit before running warm water through the hose.
Safety
A pressure washer hose carries water at high pressure, so treat the spray with respect. Never aim the spray at people or animals, and keep hands and feet clear of the nozzle. Run gas washers outdoors only, where exhaust can clear. Wear eye and hearing protection, and clear the work area of sticks, stones and loose debris before starting.
FAQ: mowing large lots
What is the standard pressure washer hose size?
There is no single standard size. The hose in this guide is 1/4 inch in inner diameter, with a 3/8 inch quick connect and M22 14 mm adapters, rated at 4200 PSI working pressure. Match the diameter, fittings and pressure rating to the washer manual, since washers vary.
How long should a pressure washer hose be?
Long enough to reach the far end of the work from where the washer sits, with slack left over. The hose in this guide is 100 ft long. Measure the distance on the property before ordering, and lay the hose flat to its full length the first time you use it.
What fittings does a pressure washer hose need?
It needs the fittings that match the washer outlet and the gun. This hose uses a 3/8 inch quick connect, and the box holds two adapters: an M22 14 mm female to 3/8 inch male plug and an M22 14 mm female to 3/8 inch female coupler. Check the threads on the washer and gun before ordering.
Can a pressure washer hose handle hot water?
Only up to its rated limit. The maker lists a max working temperature of 140 F (60 C) for this hose. Check the washer manual for its own limit before running warm water.
What pressure can a pressure washer hose take?
The maker rates this hose at 4200 PSI working pressure, with a burst pressure of 16000 PSI. Match the working pressure to the washer rating, and never run a washer whose rating sits above the hose rating.




