Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Brush Hog Maintenance: Blades, Gearbox and Greasing

A steady routine for brush hog maintenance: blades, gearbox oil, driveline grease, deck cleaning and dry storage.

Brush Hog Maintenance: Blades, Gearbox and Greasing
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1YDDVEHI Heavy Duty Brush Hog Cutter BladesYDDVEHI Heavy Duty Brush Hog Cutter Blades9.4/10View on Amazon
  2. 2HEIWUKONG 7mm Brush Hog BladesHEIWUKONG 7mm Brush Hog Blades9.3/10View on Amazon
  3. 3Yoursme 7556 Bush Hog BladesYoursme 7556 Bush Hog Blades9.6/10View on Amazon

On rough ground where a finish mower cannot go, a brush hog earns its keep: tall grass, thick weeds, brush along the fence line and the back field that has grown wild. When the cut turns ragged and the deck starts to shake, the cutter is asking for care. This guide covers brush hog maintenance in plain steps: blades, gearbox oil, driveline grease, deck cleaning and dry storage, so the cutter is ready when the field needs it.

AcreMowerLab earns a commission when you shop through links here. It never changes your price. Affiliate disclosure.

Brush hog maintenance: start with the blades

A rotary cutter has a short list of moving parts, and each part does heavy work. The table below lists the checks that matter most, then the sections that follow take them in order.

Job Check Fix
Blades Edge, bolt torque, cracks Sharpen or replace, torque to spec
Gearbox Oil level, leaks at seals Top up, reseal
Driveline Grease fittings, shields Grease, replace damaged shields
Deck Packed grass, rust Scrape clean, store dry

Blade work matters most because a dull blade strains the gearbox and the driveline. See the brush hog blades roundup for replacement options.

Inspect and sharpen the blades

Lift the deck safely, block it, and look at each blade edge. A sharp edge slices grass clean; a dull or nicked edge tears it and leaves a ragged finish. The Yoursme listing describes replacement blades that fit Bush Hog models such as the 7555, RB60 and SQ60. For torque, the Foruly listing includes a torque spec card that calls for 450 ft-lbs on the blade bolts of its skid-steer cutters, and warns that an under-torqued impact wrench is a leading cause of blade bolt failure. That figure is for those cutters only; torque your cutter’s blade bolts to the spec its manual states. The Foruly blades (on Amazon) are 12.7mm thick spring steel, while the BGQG set is 8mm thick and lists product dimensions of 13.5 inches by 3.8 inches by 3.0 inches.

A blade with a sound edge can be sharpened; a blade that is cracked, bent or worn thin should be replaced. The guide to sharpening lawn mower blades covers the edge angle and the balance check, and the blade sharpener vs new blades comparison helps decide when sharpening stops paying.

Check the gearbox oil

Gearbox oil keeps the gears turning under load. Check the level at the fill plug with the cutter level, and look for leaks around the seals and the output shaft. Milky oil or metal flakes in the oil mean water or wear inside the box, and the gearbox needs a shop look before the next job. The manual states the oil grade and the fill level; use the grade the manual lists and do not mix grades.

Grease the driveline and fittings

Grease the driveline joints and the deck fittings at the points the manual marks. Pump grease until clean grease shows at the seal, then wipe the fitting clean so dirt does not ride into the joint. A dry joint runs hot and wears fast; a greased joint runs quiet. Check the shields over the driveline: a cracked or missing shield is a safety problem, not a cosmetic flaw.

Clean the deck and store it dry

Packed grass under the deck holds moisture against the steel and feeds rust. Scrape the deck clean after the job, wash it down if the manual allows, and let it dry before storage. Store the cutter under cover, with the deck lowered or blocked, and out of standing water.

Match the cutter to the growth

Brush hogs handle tall grass, weeds and brush, and the Foruly listing describes its blades as trusted for clearing 3-inch saplings and heavy fencerows. Cutting growth beyond what the cutter is built for strains the gearbox and the driveline, so match the job to the machine and clear rocks and wire before the blades meet them.

Plan the season in passes

Walk the field before cutting and mark stumps, rocks and wire. Cut the worst ground in a pass, then come back for a second pass over the same ground. Leaving the roughest ground for a dry day keeps the deck from packing with wet cuttings.

Mind the weather and the ground

Wet ground is slippery under tires and underfoot. Skip steep or soggy ground when possible, and never cut toward a pond, ditch or road. Cold mornings make the tractor engine harder to start, so allow time and follow the manual.

Safety

Wear eye and hearing protection and sturdy shoes. Clear sticks, stones and wire before cutting, and keep children, pets and bystanders away from the work area. Shut the engine off and let the blades stop before working under the deck. Refuel the tractor only with the engine off and cool. On slopes, follow the slope limits in your tractor manual, and never let riders stand on the cutter.

FAQ: mowing large lots

How often should a brush hog be serviced?

Service the cutter at the start of the cutting season, after heavy jobs, and before storage. The manual states the service points; a cutter that works rough ground needs care more often than a cutter that only tops light grass.

How do I know the blades need sharpening?

Torn, ragged grass and a rough finish point to a dull edge, and vibration under the deck can mean a blade is bent or out of balance. Check the edge with the engine off, and sharpen or replace the blade when the edge will not cut clean.

What gear oil does a brush hog gearbox use?

The manual states the grade. Check the level at the fill plug and top up with the grade the manual lists; do not mix grades.

Can a brush hog cut saplings?

Yes, within its build. The Foruly listing describes its blades as trusted for clearing 3-inch saplings and heavy fencerows, and the BGQG set is built for thick brush and saplings. Walk the ground first and clear rocks and wire.

How should a brush hog be stored?

Clean the deck, grease the fittings, and store the cutter under cover on dry ground. A dry deck resists rust through the off season.

More mowing guides

More cutter guides sit in the brush and field mowers section of the site.

More buying guides

Brush and Field Mowers ·

How Much Is a Brush Hog: Cost Guide

A plain guide to what sets brush hog costs, how to match a cutter to a tractor and land, and what upkeep to plan…