Chainsaw Bar Maintenance: Cleaning and Oiling
Clean the bar groove, clear the oil holes and keep the bar oiled, with three bar oils compared for the job.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
EGO Power+ AOL3200 32 Fl Oz Bar and Chain Oil9.6/10View on Amazon - 2
STP Bar and Chain Oil 32 Fl Oz 12 Pack9.5/10View on Amazon - 3
DEWALT 16 oz Biodegradable Bar and Chain Oil9.4/10View on Amazon
On a wooded lot, the chainsaw earns its keep clearing fallen limbs and cutting firewood, and the bar takes the wear. Chainsaw bar maintenance means cleaning the groove, clearing the oil holes and keeping the bar oiled so the chain runs free. This guide walks through the steps in order, then shows three bar oils for the job.
AcreMowerLab earns a commission when you shop through links here. It never changes your price. Affiliate disclosure.
| # | Product | Acre Score | Buy |
|---|---|---|---|
| 1 | EGO Power+ AOL3200 32 Fl Oz Bar and Chain Oil | 9.6/10 | Buy on Amazon |
| 2 | STP Bar and Chain Oil 32 Fl Oz 12 Pack | 9.5/10 | Buy on Amazon |
| 3 | DEWALT 16 oz Biodegradable Bar and Chain Oil | 9.4/10 | Buy on Amazon |

EGO Power+ AOL3200 32 Fl Oz Bar and Chain Oil
Premium 32 fl oz bar and chain oil with anti-wear protection, rust prevention and a high tack formula, recommended for -18°F and above.
Who it's for: owners who cut in cold weather and want a stated low-temperature rating.
Who should skip it: anyone who wants a biodegradable oil or a bulk pack.
The EGO AOL3200 is a 32 fl oz bar and chain oil with a premium formula, anti-wear protection and rust and corrosion prevention. The maker lists a high tack formula that reduces kickback and recommends the oil for temperatures of -18°F and above. The bottle weighs 2.51 lb and measures 8.5 x 3.5 x 3.5 in.
Pros
- Anti-wear formula helps extend bar and chain life
- Prevents rust and corrosion on the bar
- High tack formula that the maker says reduces kickback
- Recommended for temperatures of -18°F and above
Cons
- Heavier than the 1.0 lb DEWALT bottle at 2.51 lb
- Taller than the 7.25 inch DEWALT bottle at 8.5 inches
- No biodegradable claim, unlike the DEWALT oil
- Only one size is listed

STP Bar and Chain Oil 32 Fl Oz 12 Pack
A 12-pack of 32 fl oz bar and chain oil with a ZDDP anti-wear agent and a tackifier that helps reduce throw-off.
Who it's for: owners with more than one saw, or a long cutting season, who want a bulk supply on the shelf.
Who should skip it: anyone who wants a single bottle or a stated cold-weather rating.
The STP oil comes as a 12-pack of 32 fl oz bottles, with a ZDDP anti-wear agent and a tackifier that helps reduce high-speed oil throw-off. The maker formulates the base oil to minimize resin build-up for smoother cuts, and the oil is ready for immediate use. The listing gives no temperature range or warranty term.
Pros
- ZDDP anti-wear agent helps protect the bar and chain
- Tackifier helps reduce high-speed oil throw-off
- Formulated to minimize resin build-up for smoother cuts
- A 12-pack of 32 fl oz bottles, so one order covers many refills
Cons
- Sold as a 12-pack, more oil than one saw owner may need
- No warranty term is stated
- No temperature range is stated
- No rust prevention claim is stated

DEWALT 16 oz Biodegradable Bar and Chain Oil
Biodegradable 16 oz bar and chain oil in a 1.0 lb bottle, the smallest bottle here.
Who it's for: owners who want a biodegradable oil in a small bottle for occasional cutting.
Who should skip it: anyone who wants a stated temperature range or a bulk supply.
The DEWALT oil is a biodegradable 16 oz bar and chain oil in a bottle that weighs 1.0 lb and measures 2.0 x 3.0 x 7.25 in. It is the smallest bottle here, and the listing gives no temperature range or anti-wear claim.
Pros
- Biodegradable formula
- Smallest bottle here at 16 oz, easy to carry and store
- Light bottle at 1.0 lb
- Compact footprint at 2.0 x 3.0 inches
Cons
- Only 16 oz, the smallest bottle here
- No warranty term is stated
- No temperature range is stated
- No anti-wear or tackifier claim is stated
Chainsaw bar maintenance: what the bar needs
The bar guides the chain around the cut, and oil is what keeps the chain sliding on the rails. Sawdust and sap pack into the groove, the oil holes clog, and the chain starts to drag. A clean bar with open oil holes and fresh oil is the whole job, and it is bench work you do before the saw goes back to work.
Step 1: clean the bar groove and oil holes
Take the bar off the saw, following the steps in the maker’s manual. Scrape the groove clean with a thin scraper or an old screwdriver, working the packed sawdust and sap out along the full length of the bar. Clear each oil hole with a small pick so oil can reach the chain again, then wipe the bar down and check that the groove is clear from end to end.
Step 2: check the rails and the bar tip
Look along both rails for burrs, flat spots and uneven wear. A burred rail pinches the chain, so dress any burr down with a flat file until the edge feels smooth. If your bar has a sprocket tip, spin it by hand and make sure it turns freely. A tip that sticks or grinds needs attention before the bar goes back on the saw.
Step 3: oil the bar and check the flow
Fill the oil tank with bar and chain oil and put the bar and chain back on, following the maker’s manual for tension. Run the saw briefly and watch for oil reaching the bar and chain. A dry chain after a short run means the oiler or the oil holes need another look. Use bar and chain oil for this job, not motor oil: our guide to bar and chain oil vs motor oil explains the difference.
The oil for the job
The cleaning steps above leave the bar ready for oil, and these three bar oils cover the job from a small bottle to a bulk pack.
Safety
Wear eye and hearing protection and sturdy gloves when you handle the bar and chain. Work with the saw off and the spark plug lead removed on a gas saw, or the battery out on a battery saw, and keep children, pets and bystanders away from the work area. Refuel only with the engine off and cool, and store bar oil upright, away from heat and open flame.
FAQ: mowing large lots
How often should I clean the chainsaw bar?
Clean the groove when you see sawdust packed in it or the chain starts to drag, and clean it every time you change the chain. A bar that gets cleaned on that rhythm stays oiled and runs free.
Can I use motor oil on a chainsaw bar?
Use bar and chain oil. The STP oil (on Amazon) in this guide lists a tackifier that helps reduce throw-off at speed, which is the property that keeps oil on the bar while the chain runs.
What does biodegradable bar oil do differently?
The DEWALT oil in this guide is biodegradable, so it breaks down in the ground instead of lingering the way petroleum oil does. That suits work where spilled oil reaches the soil.
What temperature can I use bar oil in?
The EGO oil in this guide is recommended for temperatures of -18°F and above. Check the label on any oil before cold-weather work.
How much oil does a chainsaw bar need?
Keep the oil tank filled and check that oil reaches the bar and chain during a cut. A dry bar and chain after a run means the oiler or the oil holes need another look.




