Chainsaw Guide Bar: How to Choose the Right Length
A chainsaw guide bar sets the deepest cut a saw can make, and its length, pitch, gauge and drive link count decide which chain fits.

On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Poulan Pro 18-in Chainsaw Guide Bar, 3/8-in Pitch, .050 Gauge9.6/10View on Amazon - 2
NIUBGONER 8-in Chainsaw Guide Bar and Chain Combo, 3/8-in Pitch, .050 Gauge, 33 Drive Links9.6/10View on Amazon - 3
KKXXDBD 20-in Chainsaw Guide Bar and Chain, .325-in Pitch, .058-in Gauge, 76 Drive Links9.6/10View on Amazon - 4
Saker 4-in Mini Chainsaw Guide Bar Replacement9.6/10View on Amazon
A property with a woodlot, a fence line and a storm-damaged oak puts a chainsaw to work most weekends, and the bar is the part that sets how much of that work the saw can reach. A chainsaw guide bar is the flat steel rail the chain runs around, and its length, pitch, gauge and drive link count decide which chain fits and how deep a cut the saw can make. This guide explains each measurement, then shows bars that cover pruning, pole saws, farm saws and full-size saws.
AcreMowerLab earns a commission when you shop through links here. It never changes your price. Affiliate disclosure.

Poulan Pro 18-in Chainsaw Guide Bar, 3/8-in Pitch, .050 Gauge
A genuine Poulan Pro 18-inch guide bar with 3/8-inch pitch and .050 gauge, a small-radius nose and a slim contour, at 1.0 pounds.
Who it's for: a Poulan Pro owner replacing a worn bar who wants the genuine part.
Who should skip it: anyone whose saw takes a different pitch or gauge, or anyone who needs a bar and chain in one box.
The Poulan Pro is a genuine Poulan Pro bar: an 18-inch guide bar with 3/8-inch pitch and .050 gauge, a small-radius nose designed to reduce kickback, and a slim contour for lightweight handling. It weighs 1.0 pounds and fits select Poulan Pro chainsaws and chains.
Pros
- Genuine Poulan Pro bar for select Poulan Pro chainsaws and chains
- 3/8-inch pitch and .050 gauge
- Small-radius nose designed to reduce kickback
- Slim contour for lightweight and maneuverable handling
Cons
- Drive link count is not stated, so count the links on the old chain
- No warranty term is stated
- Bar only, so the chain is a separate purchase
- 18-inch length suits farm work, not the largest rounds

NIUBGONER 8-in Chainsaw Guide Bar and Chain Combo, 3/8-in Pitch, .050 Gauge, 33 Drive Links
An 8-inch guide bar and chain combo with 3/8-inch pitch, .050 gauge and 33 drive links, in a 2-pack for pole saws.
Who it's for: a pole saw owner replacing a worn bar and chain who wants a spare on hand.
Who should skip it: anyone with a full-size saw, or anyone who needs a longer bar.
The NIUBGONER is an 8-inch bar and chain combo with 3/8-inch pitch, .050 gauge and 33 drive links, sold as a 2-pack. It fits Trimmer Plus PS720 pole saws and models from Harbor Freight Portland, Bauer, Sun Joe, WEN, Greenworks, Remington, Oregon, Earthwise, Husqvarna and Worx. The maker notes 8 inch is a generic term and says to count the drive links.
Pros
- 3/8-inch pitch, .050 gauge and 33 drive links
- 2-pack, so a spare bar and chain are on hand
- Fits pole saws from Trimmer Plus, Sun Joe, Greenworks, Remington and more
- 8-inch size suits pole saw work and tight spaces
Cons
- 8 inch is a generic term, so count the drive links to confirm the fit
- Bar and chain only, so the pole saw itself is separate
- 8-inch bar suits small saws, not full-size felling work
- Fits many models, so check the fit list against your saw before ordering

KKXXDBD 20-in Chainsaw Guide Bar and Chain, .325-in Pitch, .058-in Gauge, 76 Drive Links
A 20-inch guide bar and chain with .325-inch pitch, .058-inch gauge and 76 drive links, for 45cc to 62cc chainsaws.
Who it's for: a 45cc to 62cc saw owner who needs the longest bar here.
Who should skip it: anyone with a smaller saw, or anyone who needs a shorter bar for pruning.
The KKXXDBD is a 20-inch guide bar and chain with .325-inch pitch, .058-inch gauge and 76 drive links, for 45cc, 52cc, 58cc and 62cc chainsaws. The laminated bar weighs 1.8 pounds and measures about 22.5 by 2.5 by 1/8 inch. The maker gives two sizes, 22.5 by 2.5 by 1/8 inch and 5.0 by 1.0 by 22.0 inches; check before ordering.
Pros
- .325-inch pitch, .058-inch gauge and 76 drive links
- Fits 45cc, 52cc, 58cc and 62cc chainsaws
- Laminated guide bar at 1.8 pounds
- 20-inch length for the largest cuts here
Cons
- 20-inch bar suits large saws, not small saws or pruning
- Bar and chain only, so the saw is separate
- At 1.8 pounds it is heavier than the 1.0 pound Poulan
- Fits 45cc to 62cc saws only, so smaller saws need a different bar

Saker 4-in Mini Chainsaw Guide Bar Replacement
A 4-inch mini chainsaw guide bar for pruning and trimming in tight spaces, with easy installation.
Who it's for: a mini chainsaw owner who prunes in tight spaces.
Who should skip it: anyone who needs a full-size bar, or anyone who needs the pitch and gauge stated before ordering.
The Saker is a 4-inch mini guide bar for pruning and trimming in tight spaces, made for easy installation. Its compact design helps reduce the risk of kickback, and it suits woodworking, construction and landscaping as well as pruning.
Pros
- 4-inch size for precise cutting in tight spaces
- Suits pruning, trimming, woodworking, construction and landscaping
- Compact design helps reduce the risk of kickback
- Designed for easy installation
Cons
- No pitch or gauge is stated, so match it to the mini saw it replaces
- No warranty term is stated
- 4-inch bar suits pruning only, not felling or firewood
- Bar only, so the chain and saw are separate
Chainsaw guide bar: pick the right length
Bar length sets the deepest cut in a single pass, so match it to the wood, and check the saw can carry it. A short bar suits pruning, a mid bar suits farm and firewood work, and a long bar suits felling and large rounds. The four bars below run 4, 8, 18 and 20 inch, and the table sets them side by side. See the chainsaw size guide for bar length by yard work.
| Bar | Length | Pitch | Gauge | Drive links |
|---|---|---|---|---|
| KKXXDBD 20-in Bar | 20 inch | .325 inch | .058 inch | 76 |
| Poulan Pro 18-in Bar | 18 inch | 3/8 inch | .050 inch | Not stated |
| NIUBGONER 8-in Combo | 8 inch | 3/8 inch | .050 inch | 33 |
| Saker 4-in Mini Bar | 4 inch | Not stated | Not stated | Not stated |
Match pitch, gauge and drive links
Pitch is the average distance between rivets, gauge is the thickness of the drive link in the bar groove, and the drive link count is the number of drive links in the chain loop. The KKXXDBD runs .325 inch pitch, .058 inch gauge and 76 drive links. The Poulan and the NIUBGONER both run 3/8 inch pitch and .050 inch gauge, with the NIUBGONER at 33 drive links. The Saker gives no pitch or gauge figures, so match it to the mini saw it replaces and count the drive links on the old chain. Count the drive links on the chain you have: the NIUBGONER maker notes 8 inch is a generic term and says to count the drive links.
Match the bar to the saw
The bar must fit the saw it mounts on. The KKXXDBD fits 45cc, 52cc, 58cc and 62cc chainsaws, and chainsaw models 5800 and 6200. The NIUBGONER fits pole saws and small saws from Trimmer Plus, Harbor Freight Portland, Bauer, Sun Joe, WEN, Greenworks, Remington, Oregon, Earthwise, Husqvarna and Worx. The Poulan is a genuine Poulan Pro bar (on Amazon) for select Poulan Pro chainsaws and chains. The Saker is a 4-inch mini bar for a mini chainsaw; with no pitch or gauge stated, match it to the mini saw it fits.
The four bars
The gear below covers the range in this guide: a 4-inch mini bar for pruning, an 8-inch combo for pole saws, an 18-inch bar for farm saws and a 20-inch bar and chain for full-size saws.
Safety
Wear eye and hearing protection and sturdy shoes, and keep children, pets and bystanders away. Check the bar and chain match in pitch, gauge and drive links before mounting, and keep the chain sharp and tensioned to the manual. A small-radius nose, like the Poulan bar, is designed to reduce kickback, and the Saker bar helps reduce the risk of kickback in tight spaces. Clear sticks, stones and other debris before you cut, and never cut above shoulder height or with the tip of the bar.
FAQ: mowing large lots
What size guide bar do I need?
A 4-inch bar suits pruning in tight spaces, an 8-inch bar suits pole saws, an 18-inch bar suits farm and firewood work, and a 20-inch bar suits larger saws and rounds. Check pitch, gauge and drive links against the old bar before ordering.
How do I know the pitch and gauge?
Read them off the old bar or chain: the bars here run .325 inch and 3/8 inch pitch, with .058 inch and .050 inch gauge. Count the drive links, since the count and the pitch together set the chain length.
What does the drive link count mean?
It is the number of drive links in the chain loop, and it must match the bar: the KKXXDBD takes 76 drive links and the NIUBGONER takes 33. Count the drive links on the chain you have, since bar length alone does not set the count.
Can I put a longer bar on my saw?
Only if the saw has the power and the bar fits the mount: the KKXXDBD fits 45cc, 52cc, 58cc and 62cc saws, and the Poulan fits select Poulan Pro saws. Match the bar to the saw, not just the wood.
Which bar is best for pruning?
A short bar: the 4-inch Saker suits pruning and trimming in tight spaces, and the 8-inch NIUBGONER combo suits pole saw work. Short bars are easier to control in close quarters.




