ATV Snow Plow Manual Lift (2026): How It Works
A plain explanation of how a manual lift raises and lowers an ATV snow plow blade, and how to use it on driveways and farm roads.

On this page
When snow settles on the drive and the farm road, an atv snow plow manual lift is the lever that raises the blade off the ground and drops it back down to push snow, with no winch and no motor doing the lifting. The blade hangs from a push tube under the ATV, and the lift handle gives the leverage to raise it for travel and lower it for a pass. This guide explains how the lift works, how to set the blade, and what to check before the first pass of the season.
As an Amazon Associate I earn from qualifying purchases. AcreMowerLab earns a commission when you shop through links here. It never changes your price. Affiliate disclosure.
How an atv snow plow manual lift works
A manual lift is a hand lever on the push tube. Pull the lever and the blade rises off the ground so the ATV can travel to the work area; push it back and the blade drops to plow. The push tube mounts to the frame under the ATV, and the blade hangs at the front of the tube. The ECOTRIC kit (on Amazon) describes its push tube as an ergonomic pivot handle that offers improved leverage, and the mount attaches directly to the ATV frame for plowing control. Blade widths in this guide run from 43 inches to 60 inches wide, and most kits offer angle settings so the blade can throw snow to the side.
| Plow | Blade width | Angle settings |
|---|---|---|
| ECOTRIC kit | 48 in | 5 positions, up to 25 degrees |
| KEMIMOTO kit | 43 or 60 in | 5 angles |
| SNOWSQUATCH aluminum | 48 or 60 in | 5 angles |
| SNOWSQUATCH steel | 48 or 60 in | 5 angles |
| Extreme Max UniPlow | 50 in | Multi-position |
| EBESTTECH kit | 45 in | Adjustable angle |
Steel blades dominate this guide, while the SNOWSQUATCH aluminum blade is lighter than steel and will not rust. A 43 inch setup suits narrow driveways and paths, while wider setups cover farm roads and parking lots. See poly vs steel snow plow blade for the material choice, and the how to operate a snow plow guide for the pass pattern.
Step 2: mount the push tube and blade
Mount the push tube to the frame under the ATV, then pin the blade to the front of the tube. The Extreme Max UniPlow (on Amazon) mounts to the ATV frame behind the wheels, not in the front or middle, and its universal mount fits 90+% of current ATV models with a quick-release mechanism. The ECOTRIC mid-mount kit mounts to the underside of the chassis, and welded skid plates may require drilling. Some kits need minor frame changes for a proper fit, and the SNOWSQUATCH kits estimate assembly and install time at 3-4+ hours. Check the frame tube size before ordering: the KEMIMOTO mount fits a round or square frame tube no larger than 1.75 inches, and the EBESTTECH kit (on Amazon) notes 28mm frame tube holes, with separate U-bolts needed for a 38mm frame tube.
Step 3: set the blade angle
Set the blade angle before the first pass so snow rolls to the side instead of piling in front of the blade. The ECOTRIC kit offers 5 positions, with 2 to the left, center, and 2 to the right, and a maximum of 25 degrees to either side. The KEMIMOTO and SNOWSQUATCH kits offer 5 angle settings, and the KEMIMOTO blade (on Amazon) also adjusts for height. A straight blade pushes snow ahead, while an angled blade casts it to the side. See the ATV vs UTV snow plow comparison for the wider choice.
Step 4: raise and lower the blade with the lift
Use the lift handle to raise the blade when traveling between passes and lower it to plow. The manual lift works by leverage through the push tube, so the blade stays up while the ATV moves and drops when the handle is released to the plow position. Keep the blade down only while pushing snow: travel with the blade raised to avoid catching the edge on dry ground. The KEMIMOTO kit adds a spring trip action that lets the blade tilt forward when it meets rocks, curbs or other obstacles, then return to its working position.
Step 5: clear the drive in passes
Start at the center of the drive and push snow to the sides in overlapping passes, with the blade angled to cast snow off the surface. The RunNico rubber deflector (on Amazon), 72 inches by 6 inches, fits blades from 48 to 72 inches and keeps snow from flying toward the face. Overlap each pass so no strip of snow is left behind, and clear the apron at the road last so plowed street snow does not block the drive. For tires that hold grip on snow, see the best ATV tires for plowing snow picks.
Manual lift or winch lift
A manual lift raises the blade by hand leverage through the push tube. A winch lift uses an ATV winch and cable to raise the blade, and some kits require a winch: the SNOWSQUATCH kits state that a winch, not included, is required for operation, and the EBESTTECH kit notes that no winch is provided. A manual lift suits owners who want no extra wiring and no winch to maintain, while a winch lift suits owners who want powered lifting instead of hand leverage. Compare winch options in the best ATV winch roundup.
Parts that wear out
The wear bar takes the ground contact, so check it each season. The Polaris wear bar is 52 inches long, weighs 6.0 pounds, and carries a 1 Year Limited Warranty. Skid pads and adjustable skid feet set the blade height off the ground: the Extreme Max kit includes adjustable skid pads, and the EBESTTECH kit includes adjustable skid feet. See the best skid shoes picks for replacements. Shear pins protect the plow from sudden stops: the AUTOVIC shear pin is a 2-piece replacement in 4140 steel, double sided for 2 uses. The Frienda pin kit holds 4 plow push tube pins at 3/8 inch for spares. Keep spares on hand before the season starts so a worn part does not end a clearing day.
Safety
Keep people and pets clear of the blade path while plowing, and never stand in front of the blade when the ATV moves. The spring trip action on the KEMIMOTO kit lets the blade tilt forward on rocks or curbs to absorb sudden impacts. Check the wear bar, skid feet and pins before the season, and replace worn parts before they fail on the drive. On slopes, follow the ATV manual’s slope guidance. Refuel only with the engine off and cool.
FAQ: mowing large lots
What is an ATV snow plow manual lift?
A manual lift is a hand lever on the push tube that raises the blade off the ground and lowers it to plow, using leverage instead of a winch or motor.
What blade width fits a driveway?
Widths in this guide run from 43 inches to 60 inches. The 43 inch setup suits narrow driveways and paths, the 48 inch blade suits residential driveways, farm roads and parking lots, and the 50 inch blade suits residential use.
Do I need a winch with a manual lift?
No winch is needed for a manual lift, which raises the blade by hand leverage. Some kits work the other way: the SNOWSQUATCH kits state that a winch, not included, is required for operation, so check the kit before ordering.
How long does assembly take?
The SNOWSQUATCH kits estimate assembly and install time at 3-4+ hours, and some applications may require minor frame modifications for a proper fit.
How do I angle the blade?
Use the angle adjustment on the push tube mount. The ECOTRIC kit offers 5 positions, with 2 to the left, center, and 2 to the right, to a maximum of 25 degrees to either side.
What wears out on a snow plow?
The wear bar, skid pads and shear pins take the wear. The Polaris wear bar is 52 inches long, the Extreme Max kit includes adjustable skid pads, and the AUTOVIC shear pin is a 2-piece replacement in 4140 steel.
More mowing guides
- ATV vs UTV Snow Plow: Which One Should You Buy?
- Best UTV Snow Plow (2026): 4 Picks
- How to Operate a Snow Plow
- Best ATV Tires for Plowing Snow (2026)
See the ATV attachments and driveway care guides for more gear for the property.




