Box Blade Replacement Parts Guide
Box blade replacement parts matched by shank length, hole spacing, tooth taper and pin fit for grading and leveling work.

On this page
A gravel drive with ruts, a field edge that needs leveling and a garden plot ready for soil work all depend on a box blade that can still bite and grade. Box blade replacement parts are the wear pieces that restore that bite: scarifier shanks that loosen ground, teeth that meet the soil, pins that hold the assembly together and the cutting edge that levels the surface. Match each worn piece by size and fit, and the blade goes back to digging, grading and leveling work.
As an Amazon Associate I earn from qualifying purchases. AcreMowerLab earns a commission when you shop through links here. It never changes your price. Affiliate disclosure.
Box blade replacement parts: match the wear pieces
| Part | Role on the blade | Match check |
|---|---|---|
| Scarifier shanks | Loosen and break ground ahead of the box | Length, hole count and hole spacing; IDEALHOUSE states 1.5 in spacing and 0.5 in hole diameter |
| Teeth | Meet the soil at the shank tip | Taper and pin fit for the shank in use |
| Pins and fittings | Hold shanks and teeth in place | Diameter and firm fit through the shank holes |
| Cutting edge | Cuts and levels the ground surface | Edge profile and mounting pattern for the box |
Start with the piece that shows wear, then confirm fit against the box in use. Our box blade uses guide covers the jobs these parts support, from drive grading to soil leveling.
Step 2: identify the worn part
Look at the blade as a working assembly of wear pieces. Scarifier shanks do the loosening, teeth take the ground contact at the tip, pins hold shanks at the chosen depth and teeth on the shank tips, and the cutting edge does the leveling at the ground surface. A bent shank, a worn tooth, a loose pin and a dull edge each change how the blade works, and each calls for a different replacement piece. Naming the worn piece before ordering keeps the match focused on size and fit.
Step 3: measure the shank and holes
Shank fit turns on length and hole pattern. IDEALHOUSE states an 18-inch scarifier shank with four positioning holes spaced approximately 1.5 in apart and 0.5 in hole diameters, sold as a 4-pack with pins and mounting fittings. Measure the shank in use for length, count the positioning holes, and check spacing and diameter against the replacement figures before ordering. Hole pattern decides depth adjustment, so a shank with a different pattern changes how the blade sets up for digging, plowing, grading and soil preparation.
Step 4: check teeth and pins
Teeth wear at the tip where ground contact is hardest. IDEALHOUSE states removable tapered teeth held with pins, made for ground penetration and replacement when worn. A removable tooth lets the worn tip change without changing the full shank, as long as taper and pin fit match the shank in use. Check pins for firm fit through the tooth and shank holes, and keep the pin style matched to the shank pattern.
Step 5: confirm fit before ordering
Confirm the full match on paper before the parts arrive. Length, hole count, hole spacing and hole diameter must line up with the box in use, and tooth taper and pin fit must line up with the shank in use. IDEALHOUSE states reinforced steel with a black powder-coated finish for the shanks in the reference set, with a stated item weight of 28.66 pounds for the 4-pack. Material and finish matter for outdoor storage, while fit decides whether the blade works at the set depth. See types of tractor attachments for how box blades sit among other tractor tools.
Match shank length to the box
Shank length sets how deep the loosening work can run below the box. The IDEALHOUSE reference figure is an 18-inch shank, stated for compatible tractor box blades. A replacement shank longer or shorter than the shank in use changes depth range and ground clearance, even when hole pattern matches. Measure the shank in use from end to end and compare that figure with the stated replacement length. Depth adjustment through the positioning holes then sets the depth for breaking soil, backfilling, grading and leveling land.
Keep spare teeth and pins on hand
Teeth and pins are small pieces with an outsized effect on whether the blade can work. A worn tooth changes penetration, and a missing pin takes a shank out of service. Keeping spare teeth and pins matched to the shanks in use shortens downtime during grading and leveling work. Store spares with the blade so taper, diameter and fit stay matched to the set in use. For ground work choices beyond the box blade, see drag harrow vs box blade.
Work the blade on your ground
Ground type decides how hard the wear pieces work. Gravel drives ask for grading and leveling, field edges ask for breaking soil and backfilling, and garden plots ask for plowing and soil preparation. Shanks loosen, the box carries and levels, and teeth take the contact wear through each pass. Rocky or root-filled ground wears teeth faster and stresses pins, while clean soil wears edges more evenly. Match replacement timing to visible wear on teeth, pins and edge rather than to a calendar.
Store the blade and parts dry
Outdoor storage is hard on steel wear pieces. IDEALHOUSE states a black powder-coated finish on reinforced steel shanks, described by the maker as rust-resistant for outdoor work. Dry storage under cover, with shanks, teeth and pins kept together as a matched set, protects fit and finish between jobs. Clean soil from teeth and holes before storage so pins seat cleanly at the next setup. A dry, matched set goes back on the box without guesswork at the next grading job.
Safety
Park on flat ground, lower the box blade fully, shut the tractor engine off and follow the tractor and implement manuals before handling shanks, teeth or pins. Wear eye protection and sturdy gloves for steel edges and pin work. Keep children, pets and bystanders clear of the work area, and never reach under a raised implement. Support the blade so it cannot shift while pins are out. See our Safety Disclaimer.
FAQ: mowing large lots
How do you know a scarifier shank needs replacing?
Look for bent steel, worn or loose teeth, elongated holes and pins that no longer seat firmly. A shank that cannot hold depth or keep a tooth in place needs replacement, while surface wear alone calls for tooth and pin checks.
What shank length and hole spacing should you match?
Match the shank in use. IDEALHOUSE states an 18-inch shank with four positioning holes spaced approximately 1.5 in apart and 0.5 in hole diameters. Length, spacing and diameter must line up with the box in use.
Can you replace teeth without replacing the whole shank?
Yes, where the tooth is removable. IDEALHOUSE states removable tapered teeth held with pins for replacement when worn. Taper and pin fit must match the shank in use for the new tooth to seat correctly.
What pins come with replacement shanks?
IDEALHOUSE states pins and mounting fittings included with the 4-pack of shanks for attachment to compatible tractor box blades. Pin diameter and fit must match the shank holes in use.
How many shanks come in a replacement pack?
IDEALHOUSE states a 4-pack of 18-inch box blade scarifier shanks with pins and mounting fittings. Pack count must cover the shank positions in use on the box.
More mowing guides
- Box Blade Uses for Tractors and Lawns
- Tractor Bucket vs Box Blade: Which One Should You Buy?
- Drag Harrow vs Box Blade: Which One Should You Buy?
- Types of Hitch Pins for Tow-Behind Equipment
Use the Mower Matcher to narrow down choices by acreage, terrain, budget, and power type.




